Chatta subito con l'assistenza
Chat con il supporto

DR Series Software 4.0.3 - Command Line Reference Guide

Introduction to the DR Series System Command Line Reference Guide Introducing the DR Series system Managing the DR Series system
Alerts Commands Authenticate Commands Network
Network Command Usage network --show network --delete network --restart network --setdhcp network --setstatic_ip [--bondif <bondN>] [--nwif <ethN>] --ip <IPv4/IPv6 address not already in use> --netmask <netmask> [--gateway <IPv4/IPv6 address>] network --create_bond network --create_eth network --add_member network --setdns [--suffix <dns suffix>] [--primary <IPv4/IPv6 address>] [--secondary <IPv4/IPv6 address>] network --setbonding --bondif <bondN> [--mode <ALB | 802.3ad>] [--mtu <supported MTU range 512 - 9000>] network --update network --factory_reset network --host network --route network --nslookup --destination <ip address | hostname> network --traceroute --destination <ip address | hostname> network --ping --destination <ip address | hostname> [--tries <number>] [--size <number>] [--interface <bondN | ethN>] network --blink network --enable network --troubleshoot [--links] [--gateway] [--ntp] [--dns] [--active_domain] [--nis] [--clients] [--port_mapper] [--network_config] [--show_active <NFS|CIFS|OST|RDS|NDMP|ISCSI|FC>] [--interface <bondN | ethN>] network --troubleshoot --gateway --interface <bondN | ethN> network --troubleshoot [--show_active <NFS| CIFS|OST|NDMP|ISCSI|RDS>] network --tcpdump [--port <nfs | windows | replication | ost | rds>] [--pkt_size <128 - 32768>] [--file_size <0 - 100>] [--stop] [--host <ip address list>] [--interface <bondN | ethN>] network --tcpdump [--pkt_size <128 - 32768>] network --tcpdump [--file_size <0 - 100>] network --tcpdump [--host <ip address list>] network --tcpdump [--port <nfs | windows | replication | ost | rds>] network --iperf_client --server <ip address | hostname> [--port <number>] [--window_size <num bytes [KB/MB]>] [--interval <num seconds>] [--time <num seconds>] network --iperf_server [--port <number>] [--window_size <num bytes [KB/MB>] network --help
OST RDA Stats Storage Group commands System
System Command Usage system --show [--config] system --show [--hardware] system --show [--storage] [--type <boot | internal | external>] [--service_tag <service tag>] system --show [--storage] system --show [--license] [--verbose] system --show [--ntp] system --show [--version] system --show [--timezones [Region]] system --show [--upgradefile] system --show [--upgradehistory] system --show [--marker] system --show [--replication_traffic] system --show [--opdup_traffic] system --show [--backup_traffic] system --show [--mgmt_traffic] system --init system --init --secure_erase <1–pass/3-passes/7-passes> system --reboot system --shutdown system --upgrade system --license [--validate] [--add] system --setname --name <node_name> system --setdate [--date <date>] [--timezone <Region/Zone>] system --setntp [--add <server name>] system --setntp [--delete <server name>] system --setntp [--enable] system --setntp [--disable] system --setntp [--adjust_time] system --hybrid_replication [--enable][--disable][--status] system --rdairgap [--enable][--disable][--set_retention_period <0 days to 365 days>][--get_retention_period][--open][--close][--status] system --rdairgap_schedule [--start_time <HH:MM>][--end_time <HH:MM>][--remove] system --setlogin system --telnet [--enable | --disable] system --datacheck --enable system --datacheck --disable system --datacheck --throttle system --marker [--enable] [--disable] system --verify_on_read [--enable] [--disable] system --add_storage --enclosure <service tag> system --storage [--set_usage_alert <70% - 90%>] system --storage [--blink] [--type <internal | external>] [--service_tag <service tag>] [--disk <slot num>] system --storage [--unblink] [--type <internal | external>] [--service_tag <service tag>] [--disk <slot num> system --mgmt_traffic system --backup_traffic system --replication_traffic system --opdup_traffic system --help
User Virtual Machine
Maintaining the DR Series System
Diagnostics Maintenance
Maintenance Command Usage maintenance --filesystem [--start_scan [verify_data | verify_rda_metadata | verify_metadata] [--storage_group <name>] maintenance --filesystem [--stop_scan] maintenance --filesystem [--scan_status] maintenance --filesystem [--scan_report [verbose]] maintenance --filesystem [--repair_status [verbose]] maintenance --filesystem [--repair_history [verbose]] maintenance --filesystem [--scan_restart [verify_data | verify_rda_metadata | verify_metadata]] maintenance --filesystem [--repair_now] maintenance --filesystem [--reclaim_space] maintenance --filesystem [--clear_quarantine] maintenance --filesystem [--clear_quarantine] maintenance --filesystem --show_throughput maintenance --configuration [--backup] maintenance --configuration [--restore] maintenance --configuration [--reinit_dictionary] maintenance --configuration [--reset_web_certificate] maintenance --configuration --enable_sha256_web_certificate maintenance --hardware [--reinit_nvram] maintenance --hardware [--restore_hw_db] maintenance --hardware [--motherboard_replaced] maintenance --disk [--make_standby [slot num]] [--type <internal | external-<num> | service tag>] --clear_foreign] maintenance --remote_access [--show] maintenance --remote_access [--enable] maintenance --remote_access [--racreset] maintenance --remote_access [--static_ip] [--ip <IPv4/IPv6 address>] [--netmask <netmask>] [--gateway <IPv4/IPv6 address>] [--device <lom1|lom2|lom3|lom4>] maintenance --remote access [--disable] maintenance --vdisk --check_consistency --type <boot|internal|external> [--service_tag <service tag>] maintenance --help
Managing DR Series System Storage Operations
System Storage Operation Commands Connection Container VTL NDMP iSCSI FC Replication Seed Schedule
Data Integrity Checking Additional Linux Commands About us

network --iperf_client --server <ip address | hostname> [--port <number>] [--window_size <num bytes [KB/MB]>] [--interval <num seconds>] [--time <num seconds>]

The DR Series system provides the --iperf set of DR Series system CLI commands (--iperf_client and --iperf_server) that let you test network performance between any client and server on the network that you designate. In addition to testing the network performance between these two designated endpoints, this set of --iperf commands also let you test if the firewall allows a connection between these two points. You can filter the network performance test by using the following options:

--server, by the IP address or host name that you specify
--port, by the port number that you specify
--window_size, by the number of bytes, Kilobytes or Megabytes (KB/MB), that you specify
--interval, by the number of seconds that you specify
--time, by the number of seconds that you specify
NOTE: There are two conditions you must meet: 1) you must use ports with the --iperf_client and --iperf_server commands that are not in use by any other system operations (if you do not define specific ports, the --iperf_client and --iperf_server commands default to port 5001), and 2) these commands must be issued simultaneously.

Description

Tests network performance between a client and server using a designated port (use this command at the same time you use the other --iperf command).

Result

network --iperf_server [--port <number>] [--window_size <num bytes [KB/MB>]

The DR Series system provides the --iperf set of DR Series system CLI commands (--iperf_client and --iperf_server) that let you test network performance between any client and server on the network that you designate. In addition to testing the network performance between these two designated endpoints, this set of --iperf commands also let you test if the firewall allows a connection between these two points. You can filter the network performance test by using the following options:

--port, by the port number that you specify
--window_size, by the number of bytes, Kilobytes (KB) or Megabytes (MB) that you specify
NOTE: There are two conditions you must meet: 1) you must use ports with the --iperf_client and --iperf_server commands that are not in use by any other system operations (if you do not define specific ports, the --iperf_client and --iperf_server commands default to port 5001), and 2) these commands must be issued simultaneously.

Description

Tests network performance between a client and server using a designated port (use this command at the same time you use the other --iperf command).

Syntax

Result

network --help

Description

Displays the list of network-related options that can be used as a reference when using the DR Series system CLI.

Syntax

Result

network --show [--bondif <bond0,bond1,...,bondN>]
[--nwif <eth0,eth1,...,ethN>]
[--hosts]
[--routes]
[--interface <bondN|ethN>]

network --delete [--bondif <bond0,bond1,...,bondN>]
[--member <eth0,eth1,...,ethN>]
[--nwif <eth0,eth1,...,ethN>]

network --restart

network --setdhcp [--bondif <bondN>]
[--nwif <ethN>]

network --setstatic_ip [--bondif <bondN>]
[--nwif <ethN>]
--ip <IPv4/IPv6 address>
--netmask <netmask>
[--gateway <IPv4/IPv6 address>]

network --create_bond --bondif <bondN>
[--dhcp]
[--static]
--nwif <eth0,eth1,...,ethN>
[--mode < ALB | 802.3ad >]
[--name < DNS name >]
[--mtu <Supported MTU range 512 - 9000>]
[--ip <IPv4/IPv6 address>]
[--netmask <netmask>]
[--gateway <IPv4/IPv6 address>]
[--restart]

network --create_eth --nwif <ethN>
[--dhcp]
[--static]
[--name < DNS name >]
[--mtu <Supported MTU range 512 - 9000>]
[--ip <IPv4/IPv6 address>]
[--netmask <netmask>]
[--restart]

network --add_member --bondif <bondN>
--nwif <eth0,eth1,...,ethN>

network --setdns [--suffix <dns suffix>]
[--primary <IPv4/IPv6 address>]
[--secondary <IPv4/IPv6 address>]

network --setbonding [--bondif <bondN>]
[--mode < ALB | 802.3ad >]
[--mtu <Supported MTU range 512 - 9000>]

network --update [--bondif <bondN>]
[--nwif <ethN>]
[--mode < ALB | 802.3ad >]
[--name < DNS name >]
[--mtu <Supported MTU range 512 - 9000>]

network --factory_reset [--auto_bonding_speed <1G|10G>]

network --host [--add] [--ip <IPv4/IPv6 address>] [--name <host name>]
[--delete] [--ip <IPv4/IPv6 address>] [--name <host name>]

network --route [--add] [--network <destination networks>] [--netmask <netmask>] [--gateway <gateway addresses>] [--interface <bondN|ethN>]
[--delete] [--network <destination networks>] [--netmask <netmask>] [--gateway <gateway addresses>] [--interface <bondN|ethN>]

network --nslookup --destination <ip address | hostname>

network --traceroute --destination <ip address | hostname>
[--interface <bondN|ethN>]

network --ping --destination <ip address | hostname>
[--tries <number>]
[--size <number>]
[--interface <bondN|ethN>]

network --blink --nwif <ethN>

network --enable [--bondif <bond0,bond1,...,bondN>]
[--nwif <eth0,eth1,...,ethN>]

network --disable [--bondif <bond0,bond1,...,bondN>]
[--nwif <eth0,eth1,...,ethN>]

network --troubleshoot [--links]
[--gateway]
[--ntp]
[--dns]
[--active_domain]
[--nis]
[--clients]
[--port_mapper]
[--network_config]
[--show_active <NFS|CIFS|OST|RDS|NDMP|ISCSI|FC>]
[--interface <bondN|ethN>]

network --tcpdump [--port <NFS|Windows|Replication|OST|RDA>]
[--pkt_size <128 - 32768>]
[--file_size <0 - 100>]
[--stop]
[--host <ip address list>]
[--interface <bondN|ethN>]

network --iperf_client --server <ip address | hostname>
[--port <number>]
[--window_size <num bytes [KB/MB]>]
[--interval <num seconds>]
[--time <num seconds>]

network --iperf_server [--port <number>]
[--window_size <num bytes [KB/MB]>]

network --help

network <command> <command-arguments>
<command> can be one of:
--show Display network settings.
--delete Delete network interfaces(s).
--restart Restarts networking.
--setdhcp Configures bond interface to use DHCP.
--setstatic_ip Assigns a static IP address to the bond interface.
--create_bond Create bond interfaces for the machine.
--create_eth Create eth interfaces for the machine.
--add_member Add an interface to an existing bond.
--setdns Configures the Domain Name Servers.
--setbonding Updates bonding mode or MTU information.
--update Updates bonding and individual interface information.
--factory_reset Reset networking to factory configuration.
--host Manage local hosts.
--route Manage local routes.
--nslookup Looks up the IP address/hostname.
--traceroute Displays the packets route to network host.
--ping Sends ICMP ECHO_REQUEST to destination host.
--blink Blink LED on the specific ethernet device.
--enable Start the specific ethernet device(s) on restart.
--disable Don't start the specific ethernet device(s) on restart.
--troubleshoot Troubleshoots network issues.
--tcpdump Capture network traffic.
--iperf_client Run iperf (Network Performance) in client mode.
--iperf_server Run iperf (Network Performance) in server mode.

For command-specific help, please type network --help <command>
eg:
network --help show

OST

This topic introduces the set of OpenStorage Technology-related DR Series system CLI commands that enable you to perform the following tasks:

Related Documents

The document was helpful.

Seleziona valutazione

I easily found the information I needed.

Seleziona valutazione