vRanger 7.6.3 - User Guide

Selecting a destination

Selecting a destination

The Destination Selection page lets you configure the virtual data center (vDC) to which the VMware vSphere® vApp(s)™ savepoints are to be restored, and the name of the restored vApp.

To select a destination:

1	To rename the vApp you are restoring, enter the new name in the Restore vApp As field.

2	In the Restore vApp under vDC drop-down list, select the virtual data center to which the vApp should be restored.

3	For each network listed, select a network for the restored vApp in the Restore to Network column.

4	Click Next.

Mapping storage

The Restore Storage Mapping page lets you configure the storage profile and, as needed, the datastore for each VM in the vAPP.

To select storage mapping:

1	In the Storage Profile drop-down list, select the applicable storage profile.

Selecting a storage profile allows VMware® vCloud Director® to select the appropriate datastore automatically based on your storage profile settings.

2	To specify a datastore manually, select Any in the Storage Profile drop-down list, and select the applicable datastore in the Datastore drop-down list.

3	Click Next.

Selecting a restore data transport method

Selecting a restore data transport method

In vRanger, the transport determines how restore data is sent, and where the restore processing activity occurs; for more information, see VMware backup transport options. When configuring a restore job for a VMware® VM or VMware vSphere® vApp(s)™, the Restore Wizard uses the Automatic transport selection option by default to select the best transport method automatically at run-time. You can also configure the transport manually by using the Using Custom transport selection option.

 

NOTE: The Transport Selection page is not available when restoring a physical or Hyper-V® virtual server. When restoring physical servers and Hyper-V VMs, vRanger sends the data to restore over the network from the repository. Because this method is the only one available for transporting data for physical and Hyper-V servers, the Transport Selection page of the Restore Wizard does not display.

To select a restore data transport method for VMware machines, complete one of the following procedures:

•	Using Automatic transport selection

•	Using Custom transport selection

Using Automatic transport selection

The Restore Wizard includes an Automatic transport selection option, which lets vRanger select the best available method for your configuration. When determining the best transport, vRanger uses two key criteria:

•	Whether virtual appliances (VAs) are deployed.

•	Where vRanger is installed.

The logic used to select a transport differs slightly based on whether vRanger is installed on a VM or on a physical server. For more information about the order in which vRanger checks for transport availability, see Transport selection order: VM backup.

To use Automatic transport selection:

1	On the Transport Selection page, select Automatic transport selection.

The selected transport method appears at the bottom of the page.

 

IMPORTANT: Each time the job runs, vRanger detects your configuration and selects the best transport method available at run-time. That method might not always be what is shown on the page during the job setup.

2	Click Next.

Using Custom transport selection

The Custom transport selection option lets you specify both where the actual restore processing activity occurs) and which transport to use. For more information, see VMware backup transport options.

To use Custom transport selection:

1	On the Transport Selection page, select Custom transport selection.

This option enables the custom settings.

2	Select where you want the job to occur from the following options:

▪	On this vRanger machine.

▪	On a vRanger VA.

vRanger verifies whether any VAs are configured on the source host. If the host belongs to a cluster, and no host VA is found, vRanger searches for shared VAs on the cluster as well.

If no VA is detected, click Configure Virtual Appliance to add a VA to vRanger. For more information about configuring the VA, see Understanding the vRanger virtual appliance (VA).

 

NOTE: Using the vRanger VA is recommended for scalability and performance.

3	Select which transports the job should attempt from the following options:

▪	Advanced [SAN / HotAdd]

▪

LAN

For more information, see VMware backup transport options.

4	[Optional] If you want your LAN backups to be encrypted, select Use SSL encryption when transferring files over the LAN connection.

 

CAUTION: This option causes reduced performance.

5	Click Next.

Configuring restore options

Configuring restore options

The Options Selection page displays the restore options available for VMware vSphere® vApp(s)™ restore jobs.

To configure restore options:

1	On the Options Selection page, select from the following restore options:

▪	Force overwrite: This option overwrites any existing disk or config files of the same name as those files in the destination host.

▪	Force power on: This option turns on the vApp after the restore.

2	Click Next.

Setting the recurrence schedule

Setting the recurrence schedule

The Recurrence Schedule Selection page lets you indicate whether the restore job should be done on demand — at this moment — or at a future time. To schedule a future occurrence, you must define the start time, recurrence pattern, and range of recurrence.

To set the recurrence schedule:

1	On the Recurrence Schedule Selection page, select the options as described in the following table.

 

This will be an On Demand job…	There is no need to define a schedule. The job runs on demand.
Start Time	The time of day at which to run the job.
Recurrence Pattern	In this section, you establish how often the report should be generated. There are five options within this section: • Daily: The daily option can be scheduled to run the report every weekday or every x number of days. • Weekly: vRanger can be configured to run on weekly intervals, from every week to every 99 weeks. The day of the week on which to run reports can be configured. • Monthly: The monthly option offers the following configurations: ▪ Day [x] of every [y] month: x can be any value from 1 to 31. This value determines the day of the month on which the job occurs. y can be any value from 1 to 99. This value determines the monthly interval — for example, every two months sets the job to run every other month. ▪ The [f] [d] of every [y] month(s): f can be either: first, second, third, fourth or last. d can be: weekday, weekend day, Sunday, Monday, Tuesday, Wednesday, Thursday, Friday, or Saturday. y can be any value from 1 to 99. This value determines the monthly interval — for example, every two months sets the report to run every other month. • Yearly: The yearly option offers the following configurations: ▪ Every [m] [x]: m is any month of the year. This value determines the month of the year in which the report occurs. x can be any value from 1 to 31. This value determines the day of the month on which the report occurs. ▪ The [f] [d] of [m]: f can be either: first, second, third, fourth, or last. d can be: day, weekday, weekend day, Sunday, Monday, Tuesday, Wednesday, Thursday, Friday, or Saturday. m is any month of the year. This value determines the month of the year in which the report occurs. • Interval: The interval option lets you select the number of days, hours, and minutes that should pass between jobs. NOTE: The interval selected must be greater than or equal to five minutes.
Range of Recurrence	Select the starting date and ending date: • No end date: The job recurs until it is stopped. • End after: Select the number of occurrences. • End by: Select the date by which to end the recurrence.

2	Click Next.