Tchater maintenant avec le support
Tchattez avec un ingénieur du support

vRanger 7.8.5 - User Guide

Introduction vRanger overview Configuring vRanger
Configuring vRanger through the Startup Wizard Configuring vRanger manually Supplemental instructions: additional repository types
Using vRanger Backup Restore
Restoring an encrypted VMware VM Performing a full restore for VMware VMs Performing a full restore for Hyper-V® VMs Performing a full restore for VMware vApps Performing a full restore of a physical machine Performing an FLR on Windows Performing an FLR on Linux Restoring from manifest
Replicate VMs Reports Integrating and monitoring vRanger Using the vRanger Console vAPI Cmdlet details

Adding a NetVault SmartDisk repository

The following process describes how to add a Quest NetVault SmartDisk repository.

To add a NetVault SmartDisk repository:
1
In the My Repositories pane, right-click anywhere, and click Add > NetVault SmartDisk (NVSD).
2
In the Add NVSD Repository dialog box, complete the following fields:
•
Repository Name: Enter a descriptive name for the repository.
•
Description: [Optional] Enter a long-form description for the repository.
•
DNS Name or IP: Enter the IP or FQDN for the NetVault SmartDisk server.
•
User name and Password: Enter the credentials for the account that vRanger should use to connect to the repository.
 
* 
NOTE: If you have enabled WebDav authentication on your NetVault SmartDisk server, use those credentials here. If you have not enabled WebDav authentication, no credentials are required. For more information, see the Quest NetVault SmartDisk Administrator’s Guide.
•
Target Directory: This value is a logical identifier for the repository on the NetVault SmartDisk Instance, rather than a specific directory on the NetVault SmartDisk server. If you have previously created one or more repositories on the target NetVault SmartDisk Instance, the existing target directories are available in a drop-down menu.
To create a repository, enter a name for your repository.
•
Port: Enter the port that vRanger should use to connect to the NetVault SmartDisk server — the default is 37453.
•
Timeout: Enter a value that determines how long to wait before terminating an idle connection.
 
* 
NOTE: Encryption is not supported for NetVault SmartDisk repositories.
3
Click OK.
The connection to the repository is tested and the repository is added to the My Repositories pane and the Repository Information dialog box.
vRanger checks the configured repository location for existing manifest data to identify existing savepoints.
4
If vRanger finds existing savepoints, click the applicable button:
•
Import as Read-Only: To import all savepoint data into the vRanger database, but only for restores, click this button. You cannot back up data to this repository.
•
Import: To import all savepoint data into the vRanger database, click this button. vRanger is able to use the repository for backups and restores. vRanger requires read and write access to the directory.
•
Overwrite: To retain the savepoint data on the disk and not import it into vRanger, click this button. vRanger ignores the existence of the existing savepoint data and treats the repository as new.

Removing a NetVault SmartDisk repository

The process for removing a NetVault SmartDisk repository is the same as removing any other repository type.

To remove a NetVault SmartDisk repository:
1
In the My Repositories pane, right-click the NetVault SmartDisk repository, and select Remove.
The Remove Repository dialog box appears, showing the savepoints in the selected repository.
When removing a repository, you have the option of keeping the savepoints on disk or deleting them.
2
To remove the savepoints, select Delete all savepoints in this repository.
 
* 
CAUTION: This step deletes the savepoints from the repository disk, not just the vRanger database. Exercise caution when deleting savepoints.
3
If you chose to delete the savepoints, click OK when the Delete Savepoints dialog box appears.
The savepoints are deleted, along with the repository.

Adding an EMC Data Domain Boost (DD Boost) repository

The following process describes how to add an EMC® Data Domain® Boost (DD Boost™) repository. The following procedure assumes that:

•
You have a properly configured Data Domain appliance that is accessible to the vRanger machine.
•
DD Boost is licensed and enabled on the Data Domain device.
•
You have designated a DD Boost User account.
 
* 
NOTE: For information on setting up the preceding configurations, see your EMC Data Domain documentation.
To add an EMC Data Domain Boost Repository:
1
In the My Repositories pane, right-click anywhere, and click Add > EMC Data Domain Boost (DDB).
2
In the Add EMC Data Domain Boost Repository dialog box, complete the following fields:
•
Repository Name: Enter a descriptive name for the repository.
•
Description: [Optional] Enter a long-form description for the repository.
•
DNS Name or IP: Enter the IP or FQDN for the Data Domain device.
•
User name and Password: Enter the credentials for the account selected as the DD Boost User on the Data Domain device.
 
* 
NOTE: For information on creating a DD Boost user name, see your Data Domain documentation.
•
Storage Unit: This field specifies the Storage Unit configured on the Data Domain device. Select one from the drop-down menu, or enter the name for a new Storage Unit and vRanger creates one for you.
 
* 
IMPORTANT: The supported characters are alphanumeric characters and ~!@#$^_+`-={}[],.
3
Click OK.
The connection to the repository is tested and the repository is added to the My Repositories pane and the Repository Information dialog box.
vRanger checks the configured repository location for existing manifest data to identify existing savepoints.
4
If vRanger finds existing savepoints, click the applicable button:
•
Import as Read-Only: To import all savepoint data into the vRanger database, but only for restores, click this button. You cannot back up data to this repository.
•
Import: To import all savepoint data into the vRanger database, click this button. vRanger is able to use the repository for backups and restores. vRanger requires read and write access to the directory.
•
Overwrite: To retain the savepoint data on the disk and not import it into vRanger, click this button. vRanger ignores the existence of the existing savepoint data and treats the repository as new.

Configuring repository replication

Replication is configured through the My Repositories pane of the vRanger interface. The following procedure assumes that:

•
You have configured at least one DD Boost repository in vRanger.
•
At least one other Data Domain device with DD Boost enabled is available in your environment to serve as the replication target. You do not have to add this device to vRanger.
•
All devices used in replication have a Replicator license installed.
To configure replication:
1
In the My Repositories pane, right-click the Data Domain Boost repository, and select Configure Replication.
2
In the Configure Replication dialog box, complete the following fields:
•
Repository Name: Enter a descriptive name for the repository.
•
Description: [Optional] Enter a long-form description for the repository.
•
DNS Name or IP: Enter the IP or FQDN for the Data Domain device.
•
DD Boost User name and Password: Enter the credentials for the account selected as the DD Boost User on the Data Domain device.
•
Storage Unit: This field specifies the Storage Unit configured on the Data Domain device. Select one from the drop-down menu, or enter the name for a new Storage Unit and vRanger creates one for you.
3
Click OK.
The connection to the device is tested and the device is added as a repository is added to the My Repositories pane and the Repository Information dialog box.

After replication is configured for a repository, the Configure Replication option is disabled for that repository.

 
* 
IMPORTANT: After a repository is configured for replication, you must select a synchronization method before replication occurs. For information on manual and automatic synchronization options, see Managing repository replication.
Editing a replication configuration

You may edit an existing replication configuration to update credentials or timeout values. You may also use the Edit Repository Details dialog box to view free space for the repository.

1
In the My Repositories pane, right-click the EMC Data Domain Boost repository, and select Edit Replication Configuration.
2
In the Edit EMC Data Domain Boost Repository dialog box, edit any of the following fields:
•
Repository Name
•
User Name
•
Password
3
Alternatively, view the Free Space field for up-to-date information about this repository.
4
If you edited any of the fields, click Update.
 
* 
NOTE: For information on disabling repository replication, see Disabling repository replication.
Documents connexes

The document was helpful.

Sélectionner une évaluation

I easily found the information I needed.

Sélectionner une évaluation