Tchater maintenant avec le support

Obtenir une aide instantanée
Terminer l’enregistrement

Se connecter

Demander les tarifs

Contacter le service des ventes

Foglight for Storage Management Shared 4.6 - Installation Guide

Parcourir le contenu

Getting Started

Introducing the Storage Monitoring Architecture

Foglight for Storage Management Components

Foglight for Storage Management Storage Collector Agent

Network Ports Used

Sizing Your Monitored Environment Ensuring System Requirements are Met

Small Environment System Requirements Large Environment System Requirements Requirements for Agent Managers

Installing or Enabling Foglight for Storage Management

Installing Foglight for Storage Management Enabling Foglight for Storage Management from Foglight for Virtualization EE Installed Dashboards and Cartridges

Dashboards Cartridges

Adding a Full License Renewing an Expired License

Configuring Agent Managers for Storage Collection

Installing External Agent Managers Creating a Lockbox for Foglight for Storage Management Credentials

Supporting an Environment with Separate Fabrics that have Duplicated WWNs Configuring Storage Collector Agents Configuring VMware Performance Agents Configuring Hyper-V Agents Assigning Foglight for Storage Management Roles Next Steps

Configuring Agents to Monitor Storage Devices

Brocade SAN Switches

Requirements for Brocade SAN Switches

Brocade Switches on FOS 7.0 or later Brocade Switches on earlier versions of FOS

Configuring Agents to Monitor Brocade SAN Switches

Cisco SAN Switches

Requirements for Cisco SAN Switches Ensuring that SSH is Enabled on Switches Configuring Agents to Monitor Cisco SAN Switches

Dell Compellent Arrays

Requirements for Dell Compellent Arrays Configuring Agents to Monitor Dell Compellent Arrays

Dell EqualLogic PS Series Array Groups

Requirements for Dell EqualLogic Arrays Configuring Agents to Monitor Dell EqualLogic Arrays

EMC CLARiiON CX Series Arrays (CLI)

Requirements for EMC CLARiiON CX Series Arrays (CLI) Configuring Agents to Monitor EMC CLARiiON CX Series Arrays (CLI)

EMC CLARiiON, VNX, or VMAX Storage Arrays (SMI-S)

Requirements for EMC CLARiiON or VNX Arrays (SMI-S) Requirements for EMC VMAX Arrays (SMI-S) Configuring Agents to Monitor EMC Storage Arrays (SMI-S) Configuring the SMI-S Provider for EMC CLARiiON or VNX Verifying Statistics Logging is Enabled on EMC Arrays

Enabling Statistics Logging Using Unisphere Enabling Statistics Logging Using Navisphere

Requirements for EMC Isilon Configuring Agents to Monitor EMC Isilon Arrays

Requirements for EMC VPLEX Configuring Agents to Monitor EMC VPLEX Arrays

Hitachi Data Systems AMS, USP, and VSP

Requirements for Hitachi Data Systems AMS, USP, VSP Configuring Agents to Monitor Hitachi Data Systems AMS Configuring Agents to Monitor Hitachi Data Systems USP and VSP Arrays

HP EVA Storage Arrays

Requirements for HP EVA Storage Arrays Configuring Agents to Monitor HP EVA Storage Arrays

Requirements for HP 3PAR Arrays Enabling the SMI-S Provider Configuring Agents to Monitor HP 3PAR Arrays

Requirements for NetApp Filers Configuring Agents to Monitor NetApp Filers

Collection Target Support Matrix Configuration Procedures

Configuring Agents to Monitor Storage Devices Assigning Credentials

Creating and assigning new credentials Selecting and assigning an existing credential About releasing the Agent Manager lockbox

Resolving Connection Attempt Errors Configuring the Hitachi Tuning Manager Configuring Generic SMI-S Array Agent to Monitor Storage Devices

Managing Agents

Reviewing the Status of Configured Storage Collector Agents Reviewing Agent Alarms Editing Configured Agents

Reviewing Agent Status and Validating Connectivity

Validating Connectivity Properties Panel Port Property Path Property Status of Arrays

Managing Credentials

Editing existing credentials Removing a resource mapping from the Credentials dashboard

Managing Discovered Switches and Arrays

Brocade Discovered Targets Tab Arrays Discovered Targets Tab

Managing CLARiiON Domains and Arrays Managing the Hitachi Tuning Manager

Deploying Storage Agents after an Upgrade

Configuring Agents to Monitor Dell Compellent Arrays

In this procedure, you configure the agent to monitor the Compellent Storage Manager or Enterprise Manager host, then you select the arrays to monitor. For details, see Configuring Agents to Monitor Storage Devices.

Dell EqualLogic PS Series Array Groups

Foglight for Storage Management uses SNMP to collect information about Dell EqualLogic PS Series array groups. Foglight for Storage Management requires a separate agent for each Dell EqualLogic PS Series array group. The agent uses the array group’s SNMP community name to collect and organize information about the groups.For more information, see the following topics:

•

Requirements for Dell EqualLogic Arrays

•

Configuring Agents to Monitor Dell EqualLogic Arrays

Requirements for Dell EqualLogic Arrays

Your environment must meet the following requirements:

•

For supported PS Firmware, see Collection Target Support Matrix.

•

SNMP community names exist for each array group. You configure SNMP names using the EqualLogic Group Manager. For more information, see “Displaying and Configuring SNMP Access to a Group” in the EqualLogic Group Manager online help.

Configuring Agents to Monitor Dell EqualLogic Arrays

During this procedure you create an agent for an EqualLogic PS Series array group. The dialog allows you to create multiple agents for other array groups that use the same credentials.

For details, see Configuring Agents to Monitor Storage Devices.

Documents connexes

The document was helpful.

Sélectionner une évaluation

I easily found the information I needed.

Sélectionner une évaluation

© ALL RIGHTS RESERVED. Conditions d’utilisation Confidentialité Cookie Preference Center