Tchater maintenant avec le support
Tchattez avec un ingénieur du support

Archive Manager 5.9.3 - SDK Guide

SDK reference Deployment considerations for Exchange System requirements Hardware recommendations Pre-installation preparations Installing and configuring Archive Manager Upgrading/Uninstalling Archive Manager Post-installation tasks Appendix A: Attachment store types

Configuring Exchange 2010

To configure Exchange 2010:
1
Open the Exchange Management Shell.
2
Add your Archive Manager Service user account (ArchiveMgr_Service) to the "View-Only Organization Management" security role.

Sample syntax:

>Add-RoleGroupMember "View-Only Organization Management" -Member <youruseraccount>
To create a Journal Mailbox in Exchange 2010:
1
Create a new mailbox for Archive Manager on the Exchange Server. For example, name the mailbox ArchiveMgr_Journal.
2
Create a recipient object in the Microsoft Exchange Management Console. The recipient should be an Exchange 2010 mailbox set up specifically for journaling.
To implement Journaling Rules for Exchange 2010:
1
Open the Exchange Management Console to begin setting up journaling rules.
2
Under the Organization Configuration node, select Hub Transport.
3
In the Hub Transport page, select the Journal Rules tab.
4
In the Actions pane, select New Journal Rule.
5
In the Rule name box, enter a name for the journal rule you are about to create.
6
In the Send Journal reports to email address box, enter the name of the mailbox you created for journaling on the Exchange Server for Archive Manager.
This refers to the ArchiveMgr Journal mailbox created in the Create a Journal Mailbox section.
7
In the Scope field, select Global – all messages.
8
Leave the Journal messages for recipient check box unchecked.
9
Check the Enable Rule check box to activate this journaling rule for the Exchange Server.
10
Click New to save your changes.
11
Click Finish to exit the New Journal Rule wizard.
To configure the Hub Transport for Exchange 2010:

To allow the Archive Manager Website to send email using SMTP through Exchange 2010, you must configure the Hub Transport Receive Connector to accept anonymous connections.

Use the Exchange Management Console (EMC) to perform this procedure:
1
Select the Server Configuration | Hub Transport node.
2
Double-click the default connector for the Exchange server that you will use as your SMTP server for the Archive Manager Website.
3
Click on the Permission Groups tab.
4
Check the Anonymous users check box.
5
Click Apply.

Configuring and Registering a new Archive Manager application on Azure Portal

To use OAuth (Modern Authentication):

To use OAuth (Modern Authentication), an application must have an application ID issued by Azure Active Directory. Since QAM is a console application, so the user needs to register the application as a public client with Azure Active Directory. The user can register an application in the Azure Active Directory admin center.

1
Open a browser and navigate to the Azure Active Directory admin center and login using the Global Admin Account for O365 tenant.
2
Select Azure Active Directory in the left navigation pane, then select App registrations under Manage.
3
Select New registration. On the Register an application page, set the values as follows:
•
Set Name to Archive Manager.
•
For Redirect URI, change the dropdown to Public client (mobile & desktop) and set the value to https://login.microsoftonline.com/common/oauth2/nativeclient
4
Choose Register. On the next page, copy the values of the Application (client) ID and Directory (tenant) ID and save them as the user will need them later.
Configure for delegated authentication

Use the following steps to pre-configure EWS permissions.

1
Select Manifest in the left-hand navigation under Manage.
2
Locate the requiredResourceAccess property in the manifest, and add the following inside the square brackets ([]):
{
"resourceAppId": "00000002-0000-0ff1-ce00-000000000000",
"resourceAccess":
[
{
"id": "3b5f3d61-589b-4a3c-a359-5dd4b5ee5bd5",
"type": "Scope"
}
]
}
3
Select Save.
4
Select API permissions under Manage. Confirm that the EWS.AccessAsUser.All permission is listed and grant Admin Consent for the same.

Installing and configuring Archive Manager

•
Installing Archive Manager­­
•
Configuring Archive Manager
•
Useful configuration settings
•
Figure Figure Automation of Exchange Store Manager (ESM)

Installing Archive Manager­­

Installing Archive Manager­­
To access the installer for Archive Manager:
1
From the Archive Manager installation CD, run the AutoRun program.
2
Click the Install tab.
3
Under Product, click the Archive Manager link to run the installer.

In addition to providing a link to the Archive Manager installer, the AutoRun program provides other useful information about Archive Manger including: a link to distribute the Outlook Form, prerequisites and redistributables, integrations, documentation, information on the Archive Manger Online Community, and contact information.

* 
NOTE: Please refer to the System requirements chapter of this guide prior to installing Archive Manager.
To install Archive Manager:
1
On the Welcome to the Quest® Archive Manager Setup Wizard screen, click Next.
2
On the License screen, scroll through the license agreement and then select the I accept the terms of the license agreement check box and click Next to continue.
3
On the SQL Server settings screen, enter the following information:
a
Server name: The name of the SQL Server you plan to use.
To specify a SQL Server availability group, enter the availability group listener name.
b
In the Log on to the server section, select either Use Windows Authentication or Use SQL Server Authentication and specify credentials, if required. The authentication mode you specify will be used to install the Archive Manager database.
c
Database name: Enter a name for the Archive Manager database.
4
Click Next. If no database exists, the following message is displayed:
The specified database does not exist. Create it now?
If a database does exist, you will be asked if you want to upgrade.
5
Click Yes to create a new database.
6
On the Log folder screen, click Next to install to the default log folder or click Change... to select another folder.
* 
CAUTION: The Log folder should not be installed in the Archive Manager installation path.
7
On the Destination Folder screen, click Next to install to the default destination folder or click Change... to select another folder.
8
On the Custom Setup screen, select your environment and the product features to be installed. Each feature can be installed independently.
Product features include:
•
Exchange Environment
•
Active Directory Connector
•
Exchange Store Manager
•
Lync Store Manager
•
GroupWise Environment
•
GroupWise Directory Connector Service
•
GroupWise Store Manager Service
•
Data Load Service
•
Full Text Index and Search Service
•
Message Retention Policy Service
•
Alert Service
•
Website
9
The Features to Install screen displays the features that you have selected for installation, and the prerequisite software that will also be installed. If the list is correct, click Next.
10
On the Ready to install Quest® Archive Manager screen, click Install to begin the installation. If you want to review or change any of your installation options prior to starting the installer, click Back to go to the previous screens.
11
The Installing Quest® Archive Manager screen provides installation status messages as the installation progresses.
12
The Completed the Quest® Archive Manager Setup Wizard screen is displayed when the installation has completed. The Launch the Configuration Console when setup exits check box is checked by default. If you do not want to go straight to the Configuration Console, deselect the check box.
If there were any problems installing the prerequisites, a View Installation Warnings check box is displayed. Select this check box to get detailed list of the installation warnings.
13
Click Finish to exit the setup wizard and launch the Configuration Console if you have selected to do so.
* 
NOTE: If a SQL Server availability group has been specified when you install Archive Manager, you must add the databases Archivemanager (the one you specified in Step 3) and Aftermail_TEMP to the Availability Databases of the owner node after the installation. To check which is the owner node with Failover Cluster Manager, expand the cluster name, and click Roles.
Documents connexes

The document was helpful.

Sélectionner une évaluation

I easily found the information I needed.

Sélectionner une évaluation