立即与支持人员聊天
与支持团队交流

NetVault Plug-in for SnapMirror to Tape 10.0.5 - User Guide

Adding a NetApp filer

To start using the plug-in for backups and restores, you must add the applicable NetApp filers to the plug-in, and configure a user account to log on to the filer.
To add an NDMP Server
1
In the Navigation pane, click Create Backup Job.
— or —
In the Navigation pane, click Guided Configuration, and then on the NetVault Configuration Wizard page, click Create Backup Jobs.
2
Click Create New next to the Selections list to open the NetVault Backup Selections page.
3
Open the NetVault Backup Server. Select NDMP SnapMirror to Tape, and in the Actions list, click Add Server.
4
In the NDMP Server dialog box, configure the following settings.
 
Table 1. Add NDMP Server
Option
Description
Name
Type a name for the filer. The filer name must be unique. You can assign the actual name of the filer to easily identify it in the NetVault Backup environment.
NOTE: You cannot change the server name once it is configured.
Address(es)
Type the IP address of the filer. To configure multiple addresses, separate them using a comma.
If you are using Clustered Data ONTAP 8.3, specify the IP address of the Cluster Management Logical Interface (LIF) or Node Management LIF.
Port
By default, the filer is configured to listen on port number 10000.
Unless otherwise required, do not change the listener port for the filer.
Account
Specify a user account that can be used to log on to the filer. The user account must have necessary privileges to perform NDMP backups and restores.
Password
Type the password for the user account.
Use UTF-8 Conversions
Select this check box to convert the filenames and display them correctly according to the locale configured on the NetVault WebUI. This feature can only be used if the filer supports UTF-8 encoding.
To use this feature, do the following:
•
Enable UTF-8 conversion on the filer.
•
Set the appropriate language type on each target volume.
•
Set the configuration option Codepage for UTF-8 Conversions for the Plug‑in for SnapMirror to Tape. For more information, see Configuring default settings.
NOTE: For NetApp filers, the actual conversion is specified on a per-job basis by setting plug-in option Request Unicode File Information. However, the Use UTF-8 Conversions check box must be selected to use this feature.
5
Click OK to add the filer.

Editing server details

To edit the server details
1
Start the Backup Job Wizard, and click Create New next to the Selections list.
2
Open the NetVault Backup Server, and then open NDMP SnapMirror to Tape.
3
Select the filer, and in the Actions list, click Edit Server.
4
Reconfigure the applicable settings. For more information about these settings, see Add NDMP Server.
Note the following:
•
You cannot change the server name.
•
To change the password, select the New Password check box, and type the password.
5
Click OK to save the new settings.

Removing a server

To remove a server
1
Start the Backup Job Wizard, and click Create New next to the Selections list.
2
Open the NetVault Backup Server, and then open NDMP SnapMirror to Tape.
3
Select the filer, and in the Actions list, click Remove Server.
4
In the confirmation dialog box, click OK.

Configuring NetVault Backup user account

When backing up multiple volumes, the plug-in uses the “default” user account to run child jobs. If you assign a new password to this user account, you must also update the account details for the plug-in. Otherwise, the backup jobs that include multiple volumes report an error (“unable to log on to auditor, check account and password are valid”) and fail.
To configure password for the “default” user account
1
Start the Backup Job Wizard, and click Create New next to the Selections list.
2
Open the NetVault Backup Server, and then open NDMP Client.
3
Select the filer, and in the Actions list, click Set Account.
4
In the NetVault Account dialog box, provide the following information:
•
Account: Type “default”, which is the user account used to run subjobs.
•
New Password: Select the New Password check box, and specify the password for the “default” account.
5
Click OK to save the information.
相关文档

The document was helpful.

选择评级

I easily found the information I needed.

选择评级