立即与支持人员聊天
与支持团队交流

NetVault 13.3.2 - Built-in Plug-ins User Guide

Creating a consolidated saveset

To perform a backup consolidation job:
1
In the Navigation pane, click Create Backup Job.
You can also start the wizard from the Guided Configuration link. In the Navigation pane, click Guided Configuration, and then on the NetVault Configuration Wizard page, click Create Backup Jobs.
2
In Job Name, specify a name for the job. Assign a descriptive name that allows you to easily identify the job for monitoring its progress or restoring data.
A job name can contain alphanumeric and non-alphanumeric characters, but it cannot include non-Latin characters. There is no length restriction. However, a maximum of 40 characters is recommended on all platforms.
3
In the Selections list, select an existing Backup Selection Set, or complete the following steps to create a set.
a
Click Create New to open the NetVault Selections page.
b
Open the NetVault Server, and in the list of plug-ins, open Consolidate Incremental Backups.
•
In Managed Service Providers (MSP) environment, the tenant must:
Open the NetVault Client node, and in the list of plug-ins, open Consolidate Incremental Backup.
 
* 
NOTE: In Managed Service Providers (MSP) environment, to define and submit consolidate incremental backup jobs from NetVault client is supported from NetVault Backup 12.2 release onwards. To use plug-in for consolidation on the available clients you need to install or upgrade latest NetVault Server and Client.
c
To consolidate all backups up to the selected backup:
•
Open the Backup Jobs node, and in the list of NetVault machines, open the client from which the data was backed up.
•
Select the last backup up to which you want to create a consolidated saveset.
d
To consolidate all backups up to the most recent backup created using a Backup Selection Set:
•
Open the Backup Sets node, and in the list of NetVault machines, open the client for which the set was created.
•
Select the Backup Selection Set that was used to create the Full and Incremental Backups.
e
Click Save, and in the Create New Set dialog box, type a name for the set. Click Save to close the dialog box.
 
* 
NOTE: A set name can contain alphanumeric and non-alphanumeric characters, but it cannot include non‑Latin characters. On Linux OS, the names can have a maximum of 200 characters. On Windows OS, there is no length restriction. However, a maximum of 40 characters is recommended on all platforms
4
In the Plugin Options list, select an existing Backup Options Set, or complete the following steps to create a set.
a
Click Create New to open the Consolidate Options page.
b
Configure the following option:
•
Run consolidation on client: By default, the consolidation job runs on the NetVault Server. To run the job on a different NetVault machine, select the client in the list.
c
Click Save, and in the Create New Set dialog box, type a name for the set. Click Save to close the dialog box.
5
Select or create the Schedule Set, Source Set, Target Set, and Advanced Options Set. For more information about these sets, see the Quest NetVault Administrator’s Guide.
6
To submit the job for scheduling, click Save & Submit. You can monitor the job progress from the Job Status page and view the logs from the View Logs page.
To save the job definition without scheduling it, click Save. You can view, edit, or run this job from the Manage Job Definitions page. This job is not displayed on the Job Status page until you submit it.
For more information about Job Status, View Logs, and Manage Job Definitions, see the Quest NetVault Administrator’s Guide.

Restoring a consolidated saveset

For a restore job, you can use either the original savesets (Full, Incremental, and Differential savesets) or the Consolidated saveset created using these backups. The procedure for restoring data is the same for the original and the consolidated savesets. For information about restoring the data, see the relevant section in the Quest NetVault Plug-in for FileSystem User's Guide.

 

Using Plug-in for Data Copy

Using Plug-in for Data Copy
•
About Data Copy methods
•
Configuring default settings
•
Performing a Data Copy job
•
Restoring a Data Copy

About Data Copy methods

The Plug-in for Data Copy offers the following methods:

•
Backups: This method can be used to create a copy of selected backup. It can be used to perform non‑repeating Data Copy jobs.
To use Data Copy for continuous data protection (CDP) savesets of Plug-in for Microsoft 365 backups, use Backups. This method copies both Full and Incremental backups. For more information, see the NetVault Plug-in for Microsoft 365 User’s Guide.
To Data Copy continuous data protection (CDP) savesets of Plug-in for VMware backups, use Backup. For CDP VMware backups this method can copy either Full or synthetic Full backup or Incremental backup. If incremental backup is selected not copy the previous chain. For more information, see the NetVault Plug-in for VMware User’s Guide.
•
Backup Sets: This method can be used to create copy of the most recent backup created using the selected Backup Selection Set. The Backup Sets method is recommended when you want to perform regular Data Copy jobs.
..
 
* 
IMPORTANT:  
•
You cannot use the Plug-in for Data Copy to create copies of backups that were created using the Archive option.
•
You cannot use the Plug-in for Data Copy to create copies of Data Copy backups that were created using the Secondary Copy method or the Plug-in for Data Copy. In other words, you cannot use a Data Copy backup to create another Data Copy.
相关文档

The document was helpful.

选择评级

I easily found the information I needed.

选择评级