立即与支持人员聊天
与支持团队交流

On Demand Migration Current - Entra ID for Devices User Guide

FAQs

General FAQs

What ports does the agent use to connect?  

The Active Directory Agent uses three outbound ports

  • TCP 443/80
  • UDP 3030

 

I’ve installed the agent and the device isn’t ready, what do I do?  

On startup the Active Directory agent will phone home sometime in the first four hours. This communication offset time is an agent specific random and evenly distributed offset so the initial communications of a large number of devices set up at once will be spaced out and not overload the servers. If your device has the agent installed but you haven’t waited up to four hours yet, wait up to four hours and then re-check the Ready Devices list to see if your device shows up before proceeding to other network troubleshooting operations.

 

How do I adjust the agent polling interval?  

In Entra ID for Devices, the agent polling interval is not end user adjustable. The polling interval is every two minutes over UDP and every four hours over TCP. Should this amount of network traffic be an issue contact Support to investigate reducing the polling interval. Note that reducing the polling interval will cause queued migration actions to take longer to be picked up by the agents.

 

How many migration actions can I queue at once?  

In Entra ID for Devices you can queue as many migration actions at once as you would like. There is a hard limit of 600 agents per each two minutes who will be notified by the job availability cache that they have a job waiting for them. Therefore the minimum amount of time which could be required for those queued migration actions to be picked up will be the number of queued migration actions divided by 600 and multiplied by two minutes.

 

Agent last contact time isn’t updating every two minutes is something wrong?  

In Entra ID for Devices, the Agent last contact time is updated based on the TCP connection with the back end. This will occur if a job is retrieved or every 4 hours as a fall back. It is not expected that the agent last contact time will update every two minutes even if the UDP requests to the job availability cache are functioning correctly.

 

The machine name was changed during the migration project, will it keep working?  

Changing the machine name during a migration project may have unexpected implications. We recommend that you avoid doing so if possible. If not, you will need to delete the device from Entra ID for Devices and reinstall the agent. Use the Status Resets action to reset the registration status of the device, then set the Workflow to reconcile on next run and run it. This will delete the old device from the database. Finally, reinstall the Active Directory Agent on that device and run the Workflow again to read it in.

 

How do I remove Devices from Entra ID for Devices?  

To delete registered Devices from Entra ID for Devices, first use the Status Resets action to clear their registration status, then run the related Workflow with the setting ‘Reconcile on next run’ enabled. Any unregistered device records in scope of the Workflow will be removed from the database during a reconcile.

Additional Info

Architecture

The first step towards success on a project using Entra ID for Devices is to understand the product architecture and how this architecture will operate in your environment.

Entra ID for Devices consists of the following components:

  • A directory synchronization engine

  • A REST based web service

  • A management interface

  • A lightweight agent for workstations and member servers

The directory synchronization engine, the web service, and the management interface will all access the same SQL database. In most scenarios, these components will be installed on the same system. In larger or more complex network environments, the components can be distributed across multiple systems.

User workstations, member servers and computers are collectively referred to as Devices in Entra ID for Devices. Computers communicate with the Entra ID for Devices web service using the Active Directory Agent. The Active Directory Agent is a lightweight application that installs as a service on Windows computers.

To ensure that no firewall exceptions are required, the web service does not “call” the Devices to be migrated. Instead, the Active Directory Agents contact the web service at defined polling intervals, using standard HTTPS or HTTP requests to collect jobs. Jobs include key tasks such as system discovery, updating the operating system, file system, and user profile permissions, and migrating the computer to the new domain.

 

Standard Configuration  

In the Standard Configuration for Entra ID for Devices, the Agent is deployed to each Device to be migrated. Those Agents communicate outbound to the Active Directory webserver in Azure over ports 80/443 every 4 hours, when a job is available, or when initially registering. They also communicate outbound to the Active Directory Agent job availability cache in Azure over UDP on port 3030 every 2 minutes.

Standard Configuration

 

Web Proxy Configuration  

In the Web Proxy Configuration for Entra ID for Devices, the Agent is deployed to each Device to be migrated and use of a web proxy is enabled. Those Agents communicate outbound through the defined proxy port to the Active Directory webserver in Azure over port 443 every 4 hours, when a job is available, or when initially registering. They also communicate outbound through the defined proxy port to the Active Directory Agent job availability cache in Azure on port 80 every 2 minutes.

Web Proxy Configuration

相关文档

The document was helpful.

选择评级

I easily found the information I needed.

选择评级