立即与支持人员聊天
与支持团队交流

Foglight for DB2 (Cartridge) 6.3.0 - Release Notes

UNIX server and programs

The following UNIX programs must be accessible to the user logged on to the UNIX and Linux computers:

•
On all platforms: df, du, awk, iostat, vmstat, uptime, netstat, sed, ps, uname, ls -l

In addition, the following platform-specific programs must be available:

•
On the Linux platform: /proc/vmstat, /proc/net/dev, free, /proc/cpuinfo, getconf
•
On the Solaris platform: /usr/sbin/prtconf, mpstat, pagesize, psrinfo
•
On the AIX platform: lsattr, lsdev, pagesize, bindprocessor, lsdev, oslevel
•
On the HP-UX specific platform: bdf (instead of df), sar, /var/adm/syslog/syslog.log, /usr/sbin/ioscan, getconf, /swapinfo, InfoLog (needs to be enabled)

Required privileges

For information on the required privileges, refer to the Foglight for DB2 LUW Getting Started Guide.

Supported platforms

The operating system platforms and versions of DB2 that are supported for monitoring by Foglight for DB2 LUW are the following.

Supported DB2 versions

9.5, 9.7, 10.1, 10.5, 11.1, 11.5.

Supported Operating Systems

All operating systems supported by IBM.

Linux on IBM System z support

Foglight for DB2 LUW supports the monitoring of instances that are installed on Linux on System z. The supported monitored instance versions are the same as specified in the list above for the Linux platform.

* 
NOTE: IBM® DB2® pureScale is currently not supported for Linux on IBM System z.
HADR support

Foglight for DB2 LUW supports monitoring an environment configured to use HADR by creating agents to monitor each one of the nodes separately (applies for both primary nodes and secondary).

Physical partition

Foglight for DB2 LUW supports a physical partition. When monitoring a physical partition, ensure you create the agent using the agent installer on the coordinator host.

Workgroup edition

Foglight for DB2 LUW supports monitoring a workgroup edition instance.

OS Cluster support

Foglight for DB2 LUW supports monitoring an instance that is installed in an OS cluster environment.

To enable monitoring, follow the instructions on “Host connectivity settings” screen in the installation wizard:

•
Mark the “instance residing on an OS cluster”.
•
Make sure the virtual host name point to the virtual host name. This name will be used to install the DB2 agent and the IC agent.
pureScale support

Foglight for DB2 LUW supports monitoring a pureScale environment (except on Linux on IBM System z).

Troubleshooting

This section provides a list of references which address the most commonly faced issues relating to remote connectivity, allowing for easy troubleshooting using the vendor's information knowledge base:

•
To verify TCP/IP connectivity for SQL statement collections, Management Studio (SSMS) cannot be used as other protocols may be leveraged. Instead, verify connectivity using a UDL as detailed here: https://support.microsoft.com/kb/308075/.
•
To verify the WMI connectivity using a Microsoft Windows built-in utility, see https://technet.microsoft.com/en-us/library/cc180684.aspx.
•
To troubleshoot WMI access permissions, see http://blogs.technet.com/b/askperf/archive/2007/08/14/wmi-troubleshooting-permissions.aspx.
•
For information about WMI connectivity from Windows Server 2003/Vista and later versions, see http://msdn.microsoft.com/en-us/library/aa822854(VS.85).aspx.
•
For WMI troubleshooting tips and techniques, see http://msdn.microsoft.com/en-us/library/aa394603(VS.85).aspx.
相关文档

The document was helpful.

选择评级

I easily found the information I needed.

选择评级