NetVault 13.3.2 - CLI Reference Guide

Table 52. nvjobabort
Option	Description
-servername	Specifies the name of the NetVault Server that administers the job. This option is required when a remote server administers the job. It can be omitted when a local server administers the job. The server name is case‑sensitive.
-jobid	Specifies the ID of the job that you want abort.
-instanceid	Specifies the ID of the instance that you want to abort. The default value for this option is 1.

nvjobcreate

Description

Create and schedules a backup or restore job. You can also use this utility to save a job definition without scheduling it.

The nvjobcreate utility does not provide any option to configure the Restore Options. These options must be included in the Restore Selection Set. The nvsetcreate utility provides an option that can be used to specify Restore Options in the Restore Selection Set. For more information, see nvsetcreate.

Syntax

nvjobcreate [-servername <NetVault Server Name>] -jobtitle <Job Title> [-type <Job Type>] -selectionsetname <Backup or Restore Selection Set Name>
[-selectionoptionssetname <Backup Options Set Name>][-schedulesetname <Schedule Set Name>][-targetsetname <Target Set Name>] [-advoptssetname <Advanced Options Set Name>][-jobidfile <Output Filename>] -submit -parameters <Parameter Filename> [-version]

Options

Table 53. nvjobcreate
Option	Description
-servername	Specifies the name of the NetVault Server that administers the job. This option is required when a remote server administers the job. It can be omitted when a local server administers the job. The server name is case‑sensitive.
-jobtitle	Specifies the name of the job.
-type	Specifies the job type: backup or restore. The default value for this option is “backup.”
-selectionsetname	Specifies the name of the Backup or Restore Selection Set. You can use the NetVault WebUI or the nvsetcreate utility to create this set.
-selectionoptionsset name	Specifies the name of the Backup Options Set. This option must be specified when creating a backup job. If you do not specify this option while creating a backup job, the job is created successfully. However, when you try to run the job from the CLI or WebUI, it reports an error and fails. When you try to view the job definition from the WebUI, the Manage Job Definitions — View Job page does not show any details.
-schedulesetname	Specifies the name of the Schedule Set. The job is scheduled to run immediately if you omit this option. You can use the NetVault WebUI or the nvsetcreate utility to create this set.
-targetsetname	Specifies the name of the Target Set. You can use the NetVault WebUI or the nvsetcreate utility to create this set. If you do not specify a Target Set, the default target options displayed on the NetVault WebUI are used.
-advoptssetname	Specifies the name of the Backup or Restore Advanced Options Set. You can use the NetVault WebUI or the nvsetcreate utility to create this set. If you do not specify an Advanced Options Set, the default target options displayed on the NetVault WebUI are used.
-jobidfile	Specifies the name of the output file that stores the Job ID. This option is useful if the nvjobcreate utility is configured to return the exit status instead of Job ID. For more information about the configuration option, see the Quest NetVault Administrator’s Guide. You can provide an absolute or a relative path for the file. The file stores the Job ID as a string. You can use a script to read this string. This file must be deleted manually after use.
-submit	Schedules a job and lists it as an active job. If you omit this option, the job definition is only saved and not scheduled to run. You can schedule it later using the nvjobmodify utility.
-parameters	Reads options from a parameter file. You can use any text editor to create the parameter file. Specify one option with its value per line and omit “-” before the option. Use spaces or tabs to separate the option and values. To include comments, begin the line with a “#” character. Example: # nvjobcreate example file jobtitle cli job 1 selectionsetname cliselset This file can be used with the -parameters option as follows: ./nvjobcreate -parameters example.txt
-version	Displays the build date of the NetVault distribution installed on the machine.

Note

After using the nvjobcreate command to create one or more jobs, if you run the following nvreport command, the Scheduler may crash:

nvreport -class “Defined Jobs” -format “%SelectionOptions”

Workaround: From the NetVault WebUI, open the jobs for editing and save them without any changes.

Examples

•

Create an Incremental Backup job using the Backup Selection Set “CLIENT 1 Full Data Backup” and Schedule Set “Repeating 1.” The job name is “Incremental Backup of CLIENT1” and the job is administered by a local NetVault Server:

nvjobcreate -jobtitle “Incremental Backup of CLIENT1” -type backup
-selectionsetname “CLIENT 1 Full Data Backup”
-backupoption ntfsopt_typeincr=true -schedulesetname “Repeating 1” -submit

•

Create a restore job using the Restore Selection Set “RestoreFull” and submit the job to run immediately. The job name is “Restore of Full Backup” and the backup job was administered by a remote NetVault Server “SERVER2.”

nvjobcreate -jobtitle “Restore of Full Backup” -servername SERVER2
-type restore-selectionsetname RestoreFull -submit

nvjobdelete

Description

Deletes jobs that match the specified criteria.

Syntax

nvjobdelete [-servername <NetVault Server Name>]
[-jobid <Job ID>] [-type <Job Type>]
[-jobrange <Job ID-Job ID>] [-jobtitle <Job Title>] [-client <Client Name>]
[-plugin <Plug-in Name>] [-selectionsetname <Selection Set Name>]
[-schedulesetname <Schedule Set Name>] [-targetsetname <Target Set Name>]
[-advoptssetname <Advanced Options Set Name>] [-force] [-scheduleonly] [-version]

Options

Table 54. nvjobdelete
Option	Description
-servername	Specifies the name of the target NetVault Server.
-jobid	Specifies the ID of the job that you want to delete. Only one Job ID can be specified with this option.
-type	Specifies the type of job that you want to delete: backup or restore. Use this option if you want to delete a specific job type. Do not use this option if you want to delete all job types.
-jobrange	Specifies a range of Job ID numbers corresponding to a series of jobs that you want to delete. Use a hyphen to separate the start and end Job ID numbers. Example: -jobrange 30-45
-jobtitle	Specifies the name of the job that you want to delete. You must provide the full name and enclose the name in quotation marks. Example: -jobtitle “Full_Backup_1” The -jobtitle option deletes a single job. You can use the -jobrange option with the -jobtitle option to delete multiple jobs that use the same job title.
-client	Specifies the name of the NetVault Client that served as target for the jobs. Use this option to delete all jobs for the specified client. Example -client “NV_Client_MKTG”
-plugin	Specifies the name of the plug-in used to perform the jobs. Use this option to delete all jobs that were performed using a particular plug-in. The plug-in name must be enclosed in quotation marks. Example: -plugin “File System”
-selectionsetname	Specifies the name of the Backup or Restore Selection Set that was used to create the jobs.
-schedulesetname	Specifies the name of the Schedule Set that was used to create the jobs.
-targetsetname	Specifies the name of the Target Set that was used to create the jobs.
-advoptssetname	Specifies the name of the Advanced Options Set that was used to create the jobs.
-force	Deletes matching jobs that are scheduled to run. If a job that meets the criteria set by other option is in queue (scheduled to run later), any attempt to delete it fails. Use the “-force” option to delete such jobs.
-scheduleonly	Remove jobs from the job queue without deleting them from the NetVault Database. Use this option in lieu of -force.
-version	Displays the build date of the NetVault distribution installed on the machine.

Notes

•

This note applies to the use of the following options with nvjobdelete command:

•

•

•

•

•

•

When any of these options are used alone in the syntax, all instances of a job that meet the set parameters are deleted. For example, the following command deletes all jobs for the Plug-in for FileSystem:

nvjobdelete -plugin “File System”

To delete specific jobs, use a combination of options. For example, if you specify the -jobrange option with the -plugin option, only jobs that fall into the specified Job ID range specified are deleted.

Examples

•

Delete jobs with the following Job ID numbers: 1, 5, range 7-12, range 15-19:

nvjobdelete -jobid 1 -jobid 5 -jobrange 7-12 -jobrange 15-19

•

Delete all backup jobs that have the job name “Backup of Client-A” and job ID numbers between 70 and 100:

nvjobdelete -type backup -jobtitle “Backup of Client-A” -jobrange 70-100

•

Delete all jobs for “Client-A” that use the Schedule Set “FirstTuesday”:

nvjobdelete -client Client-A -schedulesetname FirstTuesday -force

nvjobhold

Description

Places a job on hold. You can use the nvjobresume utility to resume the job later.

Syntax

nvjobhold [-servername <NetVault Server Name>] -jobid <Job ID>
[-phaseid <Phase ID>] [-version]

Options

Table 55. nvjobhold
Option	Description
-servername	Specifies the name of the NetVault Server that administers the job. This option is required when a remote server administers the job. It can be omitted when a local server administers the job. The server name is case‑sensitive.
-jobid	Specifies the ID of the job that you want to place on hold. Only one Job ID can be specified with this option.
-phaseid	Specifies the phase ID. Use this option to place a particular phase on hold. If you omit this option, all scheduled phases of the specified job are placed on hold.
-version	Displays the build date of the NetVault distribution installed on the machine.

Please select your product:

To serve you better, please complete the Purpose of your Chat:

Recommended Solutions for Your Problem

NetVault 13.3.2 - CLI Reference Guide

nvjobabort

nvjobcreate

nvjobdelete

nvjobhold