Chat now with support
Chat with Support

NetVault 11.4.5 - Administration Guide

Introduction Getting started Configuring clients Configuring storage devices Backing up data Managing policies Restoring data Managing jobs Monitoring logs Managing storage devices
Monitoring device activity Managing disk-based storage devices in table view Managing disk-based storage devices in tree view Managing tape libraries in table view Managing tape libraries in tree view Managing tape drives in table view Managing tape drives in tree view Adding shared devices
Managing storage media Managing user accounts Monitoring events and configuring notifications Reporting in NetVault Backup Working with client clusters Configuring default settings for NetVault Backup
About configuring default settings Configuring encryption settings Configuring plug-in options Configuring default settings for post-scripts Configuring default settings for Verify Plug-in Configuring Deployment Manager Settings Configuring Job Manager settings Configuring Logging Daemon settings Configuring Media Manager settings Configuring Network Manager settings Configuring Process Manager settings Configuring RAS device settings Configuring Schedule Manager settings Configuring Web Service settings Configuring Auditor Daemon settings Configuring firewall settings Configuring general settings Configuring security settings Synchronizing NetVault Time Configuring default settings for global notification methods Configuring the reporting utility Configuring NetVault Backup to use a specific VSS provider Configuring default settings using Txtconfig
Diagnostic tracing Managing diagnostic data Using the deviceconfig utility NetVault Backup processes Environment variables Network ports used by NetVault Backup Troubleshooting

Placing a job on hold

To prevent a scheduled job from running, you can place the job on hold. When you place a job on hold, its schedule is disabled until you resume the job.

To place a job on hold:
1
In the Navigation pane, click Job Status.
2
In the list of jobs, select the job, and click Hold Schedule.
3
In the confirmation dialog box, click OK.
When the schedule is suspended, the job shows a status of On hold in the Next runtime column.
 
* 
NOTE: If you restart NetVault Backup, a job on hold remains in the same state, but it is rescheduled to run at its next scheduled time. If the job cannot be rescheduled because it was scheduled to run once and this time has now elapsed, the job status is set to Did not Run. Warning messages are generated in the NetVault Backup Logs that describe why the job did not run.

Resuming a job

When you place a job on hold, its schedule is disabled until you resume the job. You can resume the scheduling of the job from the Job Status page.

To resume a job that was placed on hold:
1
In the Navigation pane, click Job Status.
2
In the list of jobs, select the job, and click Resume Schedule.
3
In the confirmation dialog box, click OK.
When the schedule is resumed, the Next runtime column is updated to display the date and time when the next instance is scheduled to run.

Determining the reason for "waiting for media" status

Determining the reason for “waiting for media” status

When a job is in Waiting for Media state, it implies that the job is unable to initiate data transfer as the target drive or media item is unavailable. The Diagnose Job method allows you to determine the exact reason for this state.

A job may be in the Waiting for Media state due to the following reasons:

•
The target media or device is in use by a different job.
•
The target device is offline.
•
The target media item is not loaded.
•
The Reuse Media option is not selected for the job. So, the job is waiting for new media.
•
No blank or reusable media item is available for the job.
To determine the exact reason for the “Waiting for Media” status:
1
In the Navigation pane, click Job Status.
2
In the list of jobs, select the job, and click Diagnose Job.
3
On the Diagnose Media Request page, you can view the following information:
•
Media Request ID: Media request ID.
•
Request Type: Backup or restore.
•
Status: Status of the media request.
•
Priority: Media request priority.
•
Client: NetVault Backup Client on which the job is running.
•
Media: Target media and group label (if specified).
•
Reuse Media: The “Reuse Media” option is selected or not.
•
Required Space: Amount of space required on the media to complete the current request.
•
Ensure backup is the first on the target media: The “Ensure This Backup is First on the Media” option is selected or not.
•
Auto-Label: The “Label Blank Media Automatically” option is selected or not.
•
Mark Read-Only After: The “Mark Media Read-Only” option is selected or not.
•
Media Format: Media format.
•
Unload on Completion: Media to be unloaded after job completion or not.
•
Drives: Drive on which the tape resides.
•
Force Local: The “Local Drives Only” option is selected or not.
•
Network Compression: The “Network Compression” option is selected or not.
The Reasons table lists the reasons why the specified device or media cannot be used for the job. The following list provides some examples:
•
Not enough space.
•
Currently unavailable.
•
The 'force local drives' option is set. This type of device is considered network attached.
 
* 
NOTE: We recommend that you perform the steps described in this section and generate a log dump file when logging a case with Quest Technical Support.

Viewing log messages for a job

To view log messages for a job:
1
To view log messages for the latest instance, do the following:
a
In the Navigation pane, click Job Status.
b
In the list of jobs, select the job, and click View Logs.
2
To view log messages for previous instances, do the following:
a
In the Navigation pane, click Manage Job Definitions or Job History.
b
In the list of available job definitions, select the job, and click View Job.
c
On the Manage Job Definitions — View Job, select the instance, and click View Logs.
Related Documents

The document was helpful.

Select Rating

I easily found the information I needed.

Select Rating