サポートと今すぐチャット
サポートとのチャット

vRanger 7.6.3 - User Guide

Introduction Configuring vRanger
Configuring vRanger through the Startup Wizard Configuring vRanger manually Supplemental instructions: additional repository types
Using vRanger Backup Restore
Restoring a physical server Performing a full restore for VMware VMs Performing a full restore for Hyper-V® VMs Performing a full restore for VMware vApps Performing a full restore of a physical machine Performing an FLR on Windows Performing an FLR on Linux Restoring from manifest
Replicate VMs Reports Integrating and monitoring vRanger Using the vRanger Console vAPI Cmdlet details
Add-BackupJobTemplate Add-CIFSRepository Add-DdbReplicationRepository Add-DdbRepository Add-EsxHost Add-HypervCluster Add-HypervHost Add-HypervRestoreJobTemplate Add-NFSRepository Add-NVSDRepository Add-PhysicalMachine Add-RdaRepository Add-ReplicationJobTemplate Add-RestoreFromManifestJobTemplate Add-RestoreJobTemplate Add-VirtualAppforLinuxFLR Add-VirtualAppforLinuxFLRVA Add-VirtualCenter Disable-Job Dismount-LinuxVolume Enable-Job Get-AddressBook Get-BackupGroupEntity Get-CatalogSearchData Get-CatalogStatus Get-ConfigOption Get-Connection Get-CurrentTemplateVersionID Get-Datastore Get-GlobalTransportFailover Get-InventoryEntities Get-IsInventoryRefreshing Get-Job Get-JobTemplate Get-MonitorLog Get-Network Get-PhysicalMachineDiskMap Get-Repository Get-RepositoryJob Get-RepositorySavePoint Get-RestoreDiskMap Get-SavepointDisk Get-SavepointManifest Get-Savepoints Get-TransportFailover Get-VirtualApplianceConfig Get-VirtualApplianceDeploymentStatus Get-VirtualApplianceReconfigStatus Get-VirtualMachinesUnderInventory Get-VmDisk Get-VMDKVolume Install-VirtualAppliance Mount-LinuxVolume New-BackupFlag New-BackupGroupMember New-Daily Schedule New-EmailAddress New-IntervalSchedule New-MonthlySchedule New-ReplicationFlag New-RestoreFlag New-SMTPServer New-TransportConfiguration New-VirtualAppliance New-WeeklySchedule New-YearlySchedule Remove-AllMount Remove-BackupGroupEntity Remove-BackupGroupMember Remove-Catalog Remove-DdbStorageUnit Remove-JobTemplate Remove-LinuxVolume Remove-Repository Remove-SavePoint Remove-VirtualAppliance Remove-VirtualApplianceConfiguration Run-JobsNow Run-ReplicationFailover Run-ResumeReplicationFailover Run-TestReplicationFailover Set-Cataloging Set-CBTonVM Set-LinuxVolume Set-MountPath Set-Resources Stop-vRangerJob Update-BackupJobTemplate Update-GlobalTransportFailover Update-HypervRestoreJobTemplate Update-Inventory Update-ReplicationJobTemplate Update-RestoreJobTemplate Update-VirtualAppliance Update-VirtualApplianceConfiguration
About us

Removing an email address

Previous Next


Configuring vRanger > Configuring vRanger manually > Configuring an SMTP server > Removing an email address

Removing an email address

Complete the steps in the following procedure to remove an email address from vRanger.

To remove an email address:
1
On the Main toolbar, click Tools > Options.
2
Under the General node on the Configuration Options page, click Email Configuration.
3
In the Email Addresses section, select the email address that you want to delete.
4
Click Remove.

The listing is deleted.

5
Click OK.

Configuring display language

Previous Next


Configuring vRanger > Configuring vRanger manually > Configuring display language

Configuring display language

vRanger lets you configure the language used when displaying the vRanger UI.

To configure display language:
1
On the Main toolbar, click Tools > Options.
2
Under the General node in the Configuration Options dialog box, click Language.
3
From the Available Languages drop-down list, select the language to be used.

If preferred, select based on system locale to make an automatic setting based on the vRanger machine’s locale setting.

4
Click OK.

Configuring a virtual appliance (VA)

Previous Next


Configuring vRanger > Configuring vRanger manually > Configuring a virtual appliance (VA)

Configuring a virtual appliance (VA)

vRanger uses a VA for Linux® FLR, standard backup and restore, and for replication to and from VMware® ESXi™ servers. The Virtual Appliance Configuration dialog box lets you add a configured VA to vRanger, and select the VA to use for Linux FLR. VAs deployed using the Virtual Appliance Deployment Wizard is added to vRanger automatically.

 
* 
NOTE: You must have deployed and configured at least one VA before you can add it to vRanger. For instructions on VA deployment, see Understanding the vRanger virtual appliance (VA).
To configure a VA:
1
In the Configuration Options dialog box, select Virtual Appliance Configuration.
2
Click Add.

The Add virtual appliance configuration dialog box appears, showing the vCenter inventory tree.

3
Browse the inventory tree, and select the VA.
4
Enter the root password for the VA, and click OK.

The VA appears in the Deployed Virtual Appliances section.

Importing a license file

Previous Next


Configuring vRanger > Configuring vRanger manually > Importing a license file

Importing a license file

Before you start this process, confirm that you have placed your license file in a location that you can reach easily.

To import a license file:
1
On the Main toolbar, click Tools > Options.
2
Under the Licensing node in the Configuration Options dialog box, click Product.
3
Click Add New License.
4
Browse to the location where you stored the license file, select it, and click Open.

The new license information is added to the dialog box.

5
Click Apply.

The dialog box refreshes with the new license information added.

6
Click OK.
関連ドキュメント

The document was helpful.

評価を選択

I easily found the information I needed.

評価を選択