サポートと今すぐチャット
サポートとのチャット

DR Series Software 4.0.3 - Command Line Reference Guide

Introduction to the DR Series System Command Line Reference Guide Introducing the DR Series system Managing the DR Series system
Alerts Commands Authenticate Commands Network
Network Command Usage network --show network --delete network --restart network --setdhcp network --setstatic_ip [--bondif <bondN>] [--nwif <ethN>] --ip <IPv4/IPv6 address not already in use> --netmask <netmask> [--gateway <IPv4/IPv6 address>] network --create_bond network --create_eth network --add_member network --setdns [--suffix <dns suffix>] [--primary <IPv4/IPv6 address>] [--secondary <IPv4/IPv6 address>] network --setbonding --bondif <bondN> [--mode <ALB | 802.3ad>] [--mtu <supported MTU range 512 - 9000>] network --update network --factory_reset network --host network --route network --nslookup --destination <ip address | hostname> network --traceroute --destination <ip address | hostname> network --ping --destination <ip address | hostname> [--tries <number>] [--size <number>] [--interface <bondN | ethN>] network --blink network --enable network --troubleshoot [--links] [--gateway] [--ntp] [--dns] [--active_domain] [--nis] [--clients] [--port_mapper] [--network_config] [--show_active <NFS|CIFS|OST|RDS|NDMP|ISCSI|FC>] [--interface <bondN | ethN>] network --troubleshoot --gateway --interface <bondN | ethN> network --troubleshoot [--show_active <NFS| CIFS|OST|NDMP|ISCSI|RDS>] network --tcpdump [--port <nfs | windows | replication | ost | rds>] [--pkt_size <128 - 32768>] [--file_size <0 - 100>] [--stop] [--host <ip address list>] [--interface <bondN | ethN>] network --tcpdump [--pkt_size <128 - 32768>] network --tcpdump [--file_size <0 - 100>] network --tcpdump [--host <ip address list>] network --tcpdump [--port <nfs | windows | replication | ost | rds>] network --iperf_client --server <ip address | hostname> [--port <number>] [--window_size <num bytes [KB/MB]>] [--interval <num seconds>] [--time <num seconds>] network --iperf_server [--port <number>] [--window_size <num bytes [KB/MB>] network --help
OST RDA Stats Storage Group commands System
System Command Usage system --show [--config] system --show [--hardware] system --show [--storage] [--type <boot | internal | external>] [--service_tag <service tag>] system --show [--storage] system --show [--license] [--verbose] system --show [--ntp] system --show [--version] system --show [--timezones [Region]] system --show [--upgradefile] system --show [--upgradehistory] system --show [--marker] system --show [--replication_traffic] system --show [--opdup_traffic] system --show [--backup_traffic] system --show [--mgmt_traffic] system --init system --init --secure_erase <1–pass/3-passes/7-passes> system --reboot system --shutdown system --upgrade system --license [--validate] [--add] system --setname --name <node_name> system --setdate [--date <date>] [--timezone <Region/Zone>] system --setntp [--add <server name>] system --setntp [--delete <server name>] system --setntp [--enable] system --setntp [--disable] system --setntp [--adjust_time] system --hybrid_replication [--enable][--disable][--status] system --rdairgap [--enable][--disable][--set_retention_period <0 days to 365 days>][--get_retention_period][--open][--close][--status] system --rdairgap_schedule [--start_time <HH:MM>][--end_time <HH:MM>][--remove] system --setlogin system --telnet [--enable | --disable] system --datacheck --enable system --datacheck --disable system --datacheck --throttle system --marker [--enable] [--disable] system --verify_on_read [--enable] [--disable] system --add_storage --enclosure <service tag> system --storage [--set_usage_alert <70% - 90%>] system --storage [--blink] [--type <internal | external>] [--service_tag <service tag>] [--disk <slot num>] system --storage [--unblink] [--type <internal | external>] [--service_tag <service tag>] [--disk <slot num> system --mgmt_traffic system --backup_traffic system --replication_traffic system --opdup_traffic system --help
User Virtual Machine
Maintaining the DR Series System
Diagnostics Maintenance
Maintenance Command Usage maintenance --filesystem [--start_scan [verify_data | verify_rda_metadata | verify_metadata] [--storage_group <name>] maintenance --filesystem [--stop_scan] maintenance --filesystem [--scan_status] maintenance --filesystem [--scan_report [verbose]] maintenance --filesystem [--repair_status [verbose]] maintenance --filesystem [--repair_history [verbose]] maintenance --filesystem [--scan_restart [verify_data | verify_rda_metadata | verify_metadata]] maintenance --filesystem [--repair_now] maintenance --filesystem [--reclaim_space] maintenance --filesystem [--clear_quarantine] maintenance --filesystem [--clear_quarantine] maintenance --filesystem --show_throughput maintenance --configuration [--backup] maintenance --configuration [--restore] maintenance --configuration [--reinit_dictionary] maintenance --configuration [--reset_web_certificate] maintenance --configuration --enable_sha256_web_certificate maintenance --hardware [--reinit_nvram] maintenance --hardware [--restore_hw_db] maintenance --hardware [--motherboard_replaced] maintenance --disk [--make_standby [slot num]] [--type <internal | external-<num> | service tag>] --clear_foreign] maintenance --remote_access [--show] maintenance --remote_access [--enable] maintenance --remote_access [--racreset] maintenance --remote_access [--static_ip] [--ip <IPv4/IPv6 address>] [--netmask <netmask>] [--gateway <IPv4/IPv6 address>] [--device <lom1|lom2|lom3|lom4>] maintenance --remote access [--disable] maintenance --vdisk --check_consistency --type <boot|internal|external> [--service_tag <service tag>] maintenance --help
Managing DR Series System Storage Operations
System Storage Operation Commands Connection Container VTL NDMP iSCSI FC Replication Seed Schedule
Data Integrity Checking Additional Linux Commands About us

connection --disable --name <name> --type <NFS|CIFS|OST|RDS>

connection --disable --name <name> --type <NFS|||RDS>

Description

Disables an existing container connection type (NFS, , , or RDS) on a DR Series system.

Syntax

connection –-disable --name acme3 --type

Result

Successfully updated connection entry.
connection Quota : Unlimited
connection Used Capacity : 5.0 GB
connection Enabled : No

connection --help

Description

Displays the listing of user and related options that you can use as a reference when using the DR Series system CLI.

Syntax

Results

Usage:

connection --show [--name <name>]
[--type <NFS|CIFS|OST|RDS|NDMP|ISCSI>]
[--verbose]

connection --add --name <name>
[--type <NFS|CIFS|OST|RDS|NDMP|ISCSI>]
[--clients <ip_address>]
[--dma <ip_address>]
[--initiator <IQN, ip_address(es), hostname, or WWPN>]
[--rootmap <nobody|root|administrator>]
[--options <NFS|CIFS mount export options>]
[--capacity <Positive decimal number>]

connection --update --name <name>
--type <NFS|CIFS|OST|RDS|NDMP|ISCSI>
[--clients <ip_address>]
[--dma <ip_address>]
[--initiator <IQN, ip_address(es), hostname, or WWPN>]
[--rootmap <nobody|root|administrator>]
[--options <NFS|CIFS mount export options>]
[--capacity <Positive decimal number>]

connection --delete --name <name>
--type <NFS|CIFS|OST|RDS|NDMP|ISCSI>
[--clients <ip_address>]

connection --enable --name <name>
--type <NFS|CIFS|OST|RDS>

connection --disable --name <name>
--type <NFS|CIFS|OST|RDS>

connection --help
connection <command> <command-arguments>
<command> can be one of:
--show Displays the current connections on a container.
--add Adds a new connection to a container.
--update Updates an existing connection.
--delete Deletes an existing connection.
--enable Enables access to a container through a connection.
--disable Disables access to a container through a connection.

For command-specific help, please type connection --help <command>
eg:
connection --help show

Container

Container Command Usage
container --show
container --show [--name <name>] [--verbose]
container --add --name <name> [--type <VTL>] [--tape_size <tape_size>][--no_of_drives <1–60>][--is_oem <yes|no>][--oem_vendor <QUEST|DELL>][--group_name <name>]
container --update --name <name> [--no_of_drives <1–60>]
container --delete --name <name>
container --delete --name <name> [--delete_files]
container --marker [--enable <Auto | CommVault | Networker | TSM | ARCserve | HP_DataProtector | Unix_Dump | BridgeHead>] [--disable <Auto | CommVault | Networker | TSM | ARCserve | HP_DataProtector | Unix_Dump | BridgeHead>] --name <name>
container --delete_files --name <name>
container --help

This topic introduces the set of DR Series system CLI commands that allow you to perform the following tasks:

•
Display the status of all current containers (summary or detail)
•
Create (and name) new containers (the DR Series system limits support to 32 containers)
•
Delete existing containers

Container Command Usage

This topic introduces the container command usage:

•
container --show [options]
•
container --add --name
•
container --delete --name [options]
•
container --marker --name <name> [--enable options] [--disable options]
•
container --delete_files --name <name>
•
container --help
* 
NOTE: If you specify a command without supplying the expected value or option, you will be prompted to provide the correct value or option.
関連ドキュメント

The document was helpful.

評価を選択

I easily found the information I needed.

評価を選択