サポートと今すぐチャット
サポートとのチャット

SharePlex 11.3 - Installation and Setup Guide

About this Guide Conventions used in this guide Revision History Installing and Setting up SharePlex on an Oracle Source
SharePlex Pre-installation Checklist for Oracle Download the SharePlex installer Install SharePlex on Linux and UNIX Set up an Oracle environment for replication Set up replication from Oracle to a different target type Installation and Setup for Cloud-Hosted Databases for Oracle Installation and setup for remote capture Installation and setup for HA cluster Generic SharePlex demonstration for Oracle Advanced SharePlex demonstrations for Oracle Database Setup Utilities Solve Installation Problems for Oracle
Installing and Setting up SharePlex on a PostgreSQL Database as Source and Service
SharePlex Pre-installation Checklist for PostgreSQL Download the SharePlex installer for PostgreSQL Install SharePlex on Linux for PostgreSQL as a Source Set up Replication from PostgreSQL to Supported Target Types Installation and Setup for Cloud-Hosted Databases for PostgreSQL Installation and Setup for Remote Capture for PostgreSQL Install SharePlex on PostgreSQL High Availability Cluster Generic SharePlex Demonstration for PostgreSQL Advanced SharePlex Demonstrations for PostgreSQL Database Setup for PostgreSQL Database Setup for PGDB as a Service Solve Installation Problems for PostgreSQL
Assign SharePlex users to security groups Solve Installation Problems Uninstall SharePlex Advanced installer options Install SharePlex as root SharePlex installed items

Solve Installation Problems

Contents
Overview

This chapter reviews some common problems that you could experience when installing or running SharePlexfor the first time after installation.

Sometimes there are special installation instructions that supersede or supplement certain instructions in this manual. In addition, there can be known issues for this version that you should be aware of during or after installation. Please read the Release Notes for the version of SharePlex that you are installing before you begin the installation process.

 

Solve installer problems

Is sp_cop shut down?

If you installed SharePlex on this system before, and you are re-installing it, the installation will return errors if SharePlex is running on this system. Shut down SharePlex using the shutdown command in sp_ctrl. If you are unable to run sp_ctrl, or if any SharePlex processes will not die, locate the process (using ps -ef | grep sp_ on Unix and Linux systems) and kill it. When all SharePlex processes have been killed, run the installation program again.

Are all systems connected to the network?

Check to see that all systems on which you are loading SharePlex are connected to the network. The network node name and IP address of each system must be established sufficiently to allow SharePlex to perform TCP operations, even though the target machines themselves are not yet configured.

Did you enter the SharePlex groups in the name service?

If your environment uses a name service such as NIS or NISPLUS, you need to add the SharePlex groups and services to the nameserver before you run the SharePlex installation program, and the SharePlex Administrator must be named in the SharePlex Admin group on the nameserver before you install SharePlex. Instructions are on page 31. If these procedures are not performed, the installation will generate an error at the point in which it attempts to verify that the groups exist.

Is the database open?

The database must be open while you are installing SharePlex.

Solve SharePlex startup problems

Solve SharePlex Startup Problems

Was the user an authorized SharePlex user?

Only a member of the SharePlex administrator group (default name is spadmin) can start sp_cop. A root user that is not a member of this group can start sp_cop, but no users (including root) will be able to connect through sp_ctrl to issue commands. For more information, see Assign SharePlex Users to Security Groups.

Was the filesystem mounted as nosuid?

On Unix and Linux systems, if the filesystem is mounted as nosuid, SharePlex must be started by the installation owner. In this case, members of the SharePlex administrator group (spadmin by default), other than the installation owner, will not be able to run SharePlex.

Solve sp_ctrl problems

Did you assign the users to the SharePlex groups?

Only one SharePlex user, the Administrator who owns the SharePlex binaries and files, is created during SharePlex installation. Other users must be assigned to the appropriate SharePlex user groups. These groups control the authorization levels for various SharePlex functions.

To issue a specific command (such as activate config or stop export), a user must have that command’s authorization level or higher. For example, a SharePlex Administrator (authorization level 1) can issue any command, but a member of the spview group can only issue status commands and a few other commands that do not directly affect the replication processes.

For more information, see Assign SharePlex Users to Security Groups.

関連ドキュメント

The document was helpful.

評価を選択

I easily found the information I needed.

評価を選択