サポートと今すぐチャット
サポートとのチャット

vRanger 7.8 - User Guide

Introduction Configuring vRanger
Configuration overview Configuring vRanger through the Startup Wizard Configuring vRanger manually Supplemental instructions: additional repository types
Using vRanger Backup Restore Replicate VMs Reports Integrating and monitoring vRanger Using the vRanger Console vAPI Cmdlet details
Add-BackupGroupEntity Add-BackupJobTemplate Add-CIFSRepository Add-DdbReplicationRepository Add-DdbRepository Add-EsxHost Add-HypervCluster Add-HypervHost Add-HypervRestoreJobTemplate Add-NFSRepository Add-NVSDRepository Add-PhysicalMachine Add-RdaRepository Add-ReplicationJobTemplate Add-RestoreFromManifestJobTemplate Add-RestoreJobTemplate Add-VirtualAppforLinuxFLR Add-VirtualAppforLinuxFLRVA Add-VirtualCenter Disable-Job Dismount-LinuxVolume Enable-Job Get-AddressBook Get-BackupGroupEntity Get-CatalogSearchData Get-CatalogStatus Get-ConfigOption Get-Connection Get-CurrentTemplateVersionID Get-Datastore Get-GlobalTransportFailover Get-InventoryEntity Get-IsInventoryRefreshing Get-Job Get-JobTemplate Get-MonitorLog Get-Network Get-PhysicalMachineDiskMap Get-Repository Get-RepositoryJob Get-RepositorySavePoint Get-RestoreDiskMap Get-SavepointDisk Get-SavepointManifest Get-Savepoints Get-TransportFailover Get-VirtualApplianceConfig Get-VirtualApplianceDeploymentStatus Get-VirtualApplianceReconfigStatus Get-VirtualMachinesUnderInventory Get-VmDisk Get-VMDKVolume Install-VirtualAppliance Mount-LinuxVolume New-BackupFlag New-BackupGroupMember New-Daily Schedule New-EmailAddress New-IntervalSchedule New-MonthlySchedule New-ReplicationFlag New-RestoreFlag New-SMTPServer New-TransportConfiguration New-VirtualAppliance New-WeeklySchedule New-YearlySchedule Remove-AllMount Remove-BackupGroupEntity Remove-BackupGroupMember Remove-Catalog Remove-DdbStorageUnit Remove-JobTemplate Remove-LinuxVolume Remove-Repository Remove-SavePoint Remove-VirtualAppliance Remove-VirtualApplianceConfiguration Run-JobsNow Run-ReplicationFailover Run-ResumeReplicationFailover Run-TestReplicationFailover Set-Cataloging Set-CBTonVM Set-LinuxVolume Set-MountPath Set-Resources Stop-vRangerJob Update-BackupJobTemplate Update-GlobalTransportFailover Update-HypervRestoreJobTemplate Update-Inventory Update-ReplicationJobTemplate Update-RestoreJobTemplate Update-VirtualAppliance Update-VirtualApplianceConfiguration
About us

Creating a replication job

Previous Next


Replicate VMs > Creating a replication job
vRanger uses a simple wizard to guide you through the process of creating a replication job. At a high level, the process includes the following steps. Each of the steps is explained in more detail in the topics that follow.
To create a replication job, complete the following tasks:
•
Selecting the source VM
•
Selecting a target host
•
Selecting the replication mode
•
Selecting replication network mapping
•
Selecting hard disks
•
Selecting replication options
•
Setting the recurrence schedule
•
Configuring email notifications
•
Starting the replication job

Selecting the source VM

Previous Next


Replicate VMs > Creating a replication job > Selecting the source VM
Complete the steps in the following procedure to select the source VM.
To select the source VM:
1
Click My Inventory.
2
Right-click the VM you want to replicate, and select Replicate <VMname>.
 
 
NOTE: If there is no VA provided for the selected VM, the Virtual Appliance Not Found window notifies you that the replication job is going to fail without a VA. For more information, see Understanding the vRanger virtual appliance (VA).
3
Enter the Job Name and Job Description, and click Next.

Selecting a target host

Previous Next


Replicate VMs > Creating a replication job > Selecting a target host
On the Select Target Host page, complete the following steps to select a target host.
To select a target host:
1
Do one of the following:
▪
Choose a Target Host from the list, and click Next.
▪
If you have pre-seeded the VM on the target host, select the host on the target side to which the source VM has been restored. For more information, see Pre-seeding replication jobs. When selecting the target VM name, ensure that you are using the same name as the source VM. vRanger appends “_VzReplicate” to the VM name on the target side.
2
[Optional] In the Select Target Host dialog box, next to Preseed VM UUID, click the browse button, and select the pre-seeded VM.
 
 
IMPORTANT: After a replication job has been saved, you cannot change the target host. If you want to replicate to a different host, you may either use VMware vSphere® vMotion® to migrate the VM to the preferred host, or create a replication job for the preferred target. If you vMotion the VM, the existing replication job should identify the change in host and adjust automatically.

Selecting the replication mode

Previous Next


Replicate VMs > Creating a replication job > Selecting the replication mode
On the Replication Mode page, you can select between differential replication and hybrid replication. For more information, see Replication modes.
To select the replication mode:
1
On the Replication Mode page, under Replication Type, select Differential Replication.
 
 
NOTE: Hybrid replication is not supported when replicating to or from VMware® ESXi™. This feature is deprecated for vRanger 7.2 and later.
2
Click Next.
関連ドキュメント

The document was helpful.

評価を選択

I easily found the information I needed.

評価を選択