Chatta subito con l'assistenza
Chat con il supporto

NetVault 11.4.5 - Administration Guide

Introduction Getting started Configuring clients Configuring storage devices Backing up data Managing policies Restoring data Managing jobs Monitoring logs Managing storage devices
Monitoring device activity Managing disk-based storage devices in table view Managing disk-based storage devices in tree view Managing tape libraries in table view Managing tape libraries in tree view Managing tape drives in table view Managing tape drives in tree view Adding shared devices
Managing storage media Managing user accounts Monitoring events and configuring notifications Reporting in NetVault Backup Working with client clusters Configuring default settings for NetVault Backup
About configuring default settings Configuring encryption settings Configuring plug-in options Configuring default settings for post-scripts Configuring default settings for Verify Plug-in Configuring Deployment Manager Settings Configuring Job Manager settings Configuring Logging Daemon settings Configuring Media Manager settings Configuring Network Manager settings Configuring Process Manager settings Configuring RAS device settings Configuring Schedule Manager settings Configuring Web Service settings Configuring Auditor Daemon settings Configuring firewall settings Configuring general settings Configuring security settings Synchronizing NetVault Time Configuring default settings for global notification methods Configuring the reporting utility Configuring NetVault Backup to use a specific VSS provider Configuring default settings using Txtconfig
Diagnostic tracing Managing diagnostic data Using the deviceconfig utility NetVault Backup processes Environment variables Network ports used by NetVault Backup Troubleshooting

Modifying a library

To modify a library, follow these steps:
1
In the Navigation pane, click Manage Devices. Select Tree View.
2
Click the applicable library, and click Modify.
3
Edit Device page appears. This page displays Library Configuration area and Selected Drives area. Click Show Drives tab to display Choose Drives area.
4
In the Library Configuration area, click the applicable library to display the library picture, type, and details in the Selected Drives area. The Selected Drives area shows the details of the first drive in the selected bay.
5
Click the library and then click Configure. Configure the parameters under the following tabs:
 
Option tab
Description

Configuration

For more information about these settings, see General settings for tape libraries.

Cleaning

For more information about these settings, see Drive cleaning settings.

Entry/Exit Ports

Select the desired options for entry/exit ports.

Mixed Media

For more information about these settings, see Mixed media settings.

SCSI Configuration

The default timeout value for the different types of SCSI commands is set to zero, which correspond to the following intervals:

•
Fast SCSI Commands – 300 seconds
•
Slow SCSI Commands – 900 seconds
•
Very Slow SCSI Commands – 3 hours

An error is logged if a command execution does not complete within the specified interval. You should not change the default timeout for any of the SCSI commands unless otherwise advised by Quest Support.

6
Click OK to close the configuration dialog box.
7
Click Save.

Changing the device view type

NetVault Backup provides two device view types:

•
Physical View – This is the default view type. This view displays the actual structure of the library, including all drives, slots, and entry/exit ports. Media are shown at their current location in the library.
•
Logical View – This view is centered around the actual media in a library. The device tree consists of two folders – Drives and Media. The libraries and drives are grouped as Drives, and the Media are grouped according to the Group Label.

To change the device view type, follow these steps:

1
In the Navigation pane, click Manage Devices.
2
Click Change View.
3
NetVault Backup will change the view from Physical to Logical or vice versa, and displays a message.

Opening and closing library door

Before opening a library door, you must issue the Open Door command from the WebUI. NetVault Backup puts a software lock on the library door to prevent anyone from opening the door without issuing the Open Door command. If you do not issue this command, NetVault Backup does not know when tapes are added, removed, or rearranged, and it may attempt to load non-existent media.

To open a library door from WebUI:
1
In the Navigation pane, click Manage Devices.
2
In the list of devices, click the icon to locate, and then click the library. Click Open Door.
The library goes offline when you open the door.
3
To bring it back online, click the library and click Close Door.

Opening and closing entry/exit ports

To open or close entry/exit ports, follow these steps:
1
In the Navigation pane, click Manage Devices.
2
In the list of devices, click the icon to locate, and then click the applicable library.
3
Click Open Entry/Exit.
4
To close the port after placing the media, click Entry/Exit Closed. If you have placed a cleaning media item in the port, click Entry/Exit Closed with Cleaning Media to move the media item to a cleaning slot in the library.
5
To bring it back online, click Close Door.
Related Documents

The document was helpful.

Seleziona valutazione

I easily found the information I needed.

Seleziona valutazione