NetVault Bare Metal Recovery 12.2 - User Guide for Plug-ins

The Plug-in Live Client checks for the required VMware driver during a backup. If the required driver is not present, the backup job completes with warnings. If recovery to a VMDK Image is not intended, the VMware driver is not required and you can update the configuration file to disable the warning.

•

To update the configuration file, perform the following steps:

Locate and open the “nvdrw.cfg” file in a text editor.

This file is located in \\NetVault Backup\config\. If the file does not exist, you can create it.

Add the following section:

[VM Option]

CheckVmDriver=FALSE

Save and close the file.

•

To install the VMware device driver, perform the following steps:

Download the VMware drivers from the Quest website.


	NOTE: For VMDK Image recovery, only SCSI drivers are supported.

Copy the required device driver, for example, “vm_lsi_2008.inf,” to the physical machine.

To install the required device driver on the physical machine, locate the file on the physical machine.

Right-click it, and select Install from the menu.

When the Hardware Installation warning message is displayed, click Continue Anyway.

Reboot the system for the new settings to take effect.

•

If the space allocated for shadow copies on the volume is insufficient, the oldest persistent shadow copy may be lost when you perform a backup. For information about shadow copies and how they are implemented, see the MSDN Library page at: http://msdn.microsoft.com/en-us/library/bb968832(VS.85).aspx

•

For instructions on allocating space for shadow copies, see: http://technet.microsoft.com/en-us/library/cc786104.aspx

Verifying access to the Plug-in Server for use with Plug-in Live Client for Windows

Before using the Plug-in Live Client to perform active backups of a target NetVault Bare Metal Recovery Client, verify that the NetVault Bare Metal Recovery Client is bootable with Plug-in Offline Client, and that it is accessible to the Plug-in Server. This procedure is performed to ensure that the target NetVault Bare Metal Recovery Client is accessible at restore time. Note the following:

•

Failure to perform this verification process may result in the inability to restore backups taken with the Plug-in Live Client.

•

You only need to perform this procedure once for a target NetVault Bare Metal Recovery Client, unless its networking hardware is changed later. If so, you must perform these procedures again.

•

This procedure must be performed for each NetVault Bare Metal Recovery Client that is to be backed up with the Plug-in Live Client.

Part 1: Boot the NetVault Bare Metal Recovery Client with Plug-in Offline Client

Boot the target NetVault Bare Metal Recovery Client with the Plug-in Offline Client to prepare it for the backup. To complete the boot routine, review all the steps in Booting a NetVault Bare Metal Recovery Client with Plug-in Offline Client.

Part 2: Verify access to the NetVault Bare Metal Recovery Client

After you have booted the NetVault Bare Metal Recovery Client using Plug-in Offline Client, outlined in Booting a NetVault Bare Metal Recovery Client with Plug-in Offline Client, access the NetVault Backup Server and start the NetVault Backup WebUI.

Access the NetVault Backup Backup window, and double-click the NetVault Backup Server — the system containing the Plug-in Server — to open it.

Open the Plug-in Server by double-clicking it.

Locate the appropriate NetVault Bare Metal Recovery Client displayed under the plug-in, and double-click it to open it.

One of two results occurs:

•

System disks are revealed: If selectable disks are revealed, you have verified that the NetVault Bare Metal Recovery Client is accessible.

•

An error message is revealed: If a dialog box displays stating “Failed to connect to client,” the NetVault Bare Metal Recovery Client is not accessible. This issue occurs for any number of reasons. The most common reason is that the networking hardware was not correctly configured during boot of the NetVault Bare Metal Recovery Client with Plug-in Offline Client. Reboot the target NetVault Bare Metal Recovery Client with Plug-in Offline Client, outlined in Booting a NetVault Bare Metal Recovery Client with Plug-in Offline Client, and ensure that the proper network-related values are used.

Verifying Disk Geometry and Device Size for use with Plug-in Live Client for Windows

The Plug-in Live Client makes it possible to view the disk geometry of a selected system. Quest recommends that you note this information before you back up a system with the Plug-in Live Client. When restoring previously backed-up data, if this information is not accounted for, a restore could fail.

From the NetVault Backup Server, start the NetVault Backup WebUI.

In the Navigation pane, click Create Backup Job.

Next to the Selections list, click Create New.

On the NetVault Backup Selections page, double-click the client that contains the Plug-in Live Client to open it.

Open the Plug-in Live Client by double-clicking it.

Double-click the applicable NetVault Bare Metal Recovery Client displayed under the plug-in to reveal the disks contained within.

To determine the Disk Geometry, click the applicable disk, and select Disk Geometry from the context menu.

The Device Geometry dialog box displays the size and quantity for various items pertaining to the selected disk.

With this information noted, click OK.

Performing an online backup of data with Windows Server 2008 or later using Plug-in Live Client for Windows

As noted in previous topics, the Plug-in Live Client lets you back up full systems and individual partitions contained within that system, while they remain online and active.

The following topics describe the steps required to complete a successful backup with Plug-in Live Client:

•

Selecting data for a backup with Plug-in Live Client for Windows using Windows Server 2008 or later

•

Setting backup options for a backup with Plug-in Live Client for Windows using Windows Server 2008 or later

•

Finalizing and submitting the job for a backup with Plug-in Live Client for Windows using Windows Server 2008 or later