Tchater maintenant avec le support
Tchattez avec un ingénieur du support

Foglight for Storage Management Shared 6.3.0 - Release Notes

Troubleshooting

Troubleshooting

This section provides a list of references which address the most commonly faced issues relating to remote connectivity, allowing for easy troubleshooting using the vendor's information knowledgebase:

 


Product licensing

Product licensing

Foglight includes a licensing capability that restricts access to those features that are defined in the license. Any Management Server installation requires a license that grants access to server-specific parts of the browser interface and the features associated with them. Foglight cartridges are also license-protected. While some cartridges are covered by the base Foglight license (such as Foglight Agent Manager cartridges and the Cartridge for Infrastructure), others may require an additional license. Foglight for Storage Management is covered by the Foglight Evolve Monitor, Operate, and Flex license.

 

To activate a trial or a purchased commercial license:

  1. On the navigation panel, under Dashboards, click Administration > Setup > Manage Licenses.
  2. Click Install.
  3. In the Install License dialog box, click Browse.
  4. In the file browser that appears, specify the location of the license file.
  5. In the Install License dialog box, click Install License.

 


Getting started with Foglight for Storage Management

Getting started with Foglight for Storage Management

Contents of the release package

The Foglight for Storage Management 6.3.0 release package contains the following:

  1. Foglight for Storage Management 6.3.0
    • Storage-6_3_0.car
    • StorageAgentSDK-1_0_4.car
    • PythonAgentSDK-1_0_5.car
    • ManagedTopologyService-1_0_3.car
    • SanHost-4_5_0.car (included in Storage-6_3_0.car)
    • SMISStorageAgent-6_3_0.car
  2. Product documentation, including:
    • User and Reference Guide (PDF and online help)
    • Release Notes (this document)

Installation instructions

Foglight for Storage Management 6.3.0 comes pre-installed and enabled on Foglight Evolve 6.3.0 or Foglight for Virtualization, Enterprise Edition 8.9.3.


To install Foglight for Storage Management on Foglight, you must install and enable the following cartridge files. The sequence of cartridge installation is important because of their dependencies:

  • Storage-6_3_0.car
  • StorageAgentSDK-1_0_4car
  • PythonAgentSDK-1_0_5.car
  • ManagedTopologyService-1_0_3.car
  • SanHost-4_5_0.car (included in Storage-6_3_0.car)
  • SMISStorageAgent-6_3_0.car

To install cartridge files, use the Administration > Cartridges > Cartridge Inventory dashboard. For full installation instructions, refer to the topic "Installing Foglight cartridges" in the Foglight Administration and Configuration Help.

Additional resources

Additional information is available from the following:

Globalization

This section contains information about installing and operating this product in non-English configurations, such as those needed by customers outside of North America. This section does not replace the materials about supported platforms and configurations found elsewhere in the product documentation.

This release was not enabled and tested for international operation. Only U.S. English configurations of this product and U.S. English datasets are fully supported. Support for non-ASCII characters or non-English configurations may work appropriately, but these configurations have not been tested and this release should be used with caution in these environments.

 


Contents of the release package

Getting started with Foglight for Storage Management

The Foglight for Storage Management 6.3.0 release package contains the following:

  1. Foglight for Storage Management 6.3.0
    • Storage-6_3_0.car
    • StorageAgentSDK-1_0_4.car
    • PythonAgentSDK-1_0_5.car
    • ManagedTopologyService-1_0_3.car
    • SanHost-4_5_0.car (included in Storage-6_3_0.car)
    • SMISStorageAgent-6_3_0.car
  2. Product documentation, including:
    • User and Reference Guide (PDF and online help)
    • Release Notes (this document)

Installation instructions

Foglight for Storage Management 6.3.0 comes pre-installed and enabled on Foglight Evolve 6.3.0 or Foglight for Virtualization, Enterprise Edition 8.9.3.


To install Foglight for Storage Management on Foglight, you must install and enable the following cartridge files. The sequence of cartridge installation is important because of their dependencies:

  • Storage-6_3_0.car
  • StorageAgentSDK-1_0_4car
  • PythonAgentSDK-1_0_5.car
  • ManagedTopologyService-1_0_3.car
  • SanHost-4_5_0.car (included in Storage-6_3_0.car)
  • SMISStorageAgent-6_3_0.car

To install cartridge files, use the Administration > Cartridges > Cartridge Inventory dashboard. For full installation instructions, refer to the topic "Installing Foglight cartridges" in the Foglight Administration and Configuration Help.

Additional resources

Additional information is available from the following:

Globalization

This section contains information about installing and operating this product in non-English configurations, such as those needed by customers outside of North America. This section does not replace the materials about supported platforms and configurations found elsewhere in the product documentation.

This release was not enabled and tested for international operation. Only U.S. English configurations of this product and U.S. English datasets are fully supported. Support for non-ASCII characters or non-English configurations may work appropriately, but these configurations have not been tested and this release should be used with caution in these environments.

 


Documents connexes

The document was helpful.

Sélectionner une évaluation

I easily found the information I needed.

Sélectionner une évaluation