Tchater maintenant avec le support
Tchattez avec un ingénieur du support

NetVault Plug-in for Hyper-V 11.2 - User Guide

Prerequisites for installing the plug-in

Before installing Plug‑in for Hyper‑V, verify that the following prerequisites are met on the system designated as the Hyper‑V Server.

•
Install Windows PowerShell and configure the execution policy: Before you can use the plug-in, PowerShell 3.0 or later must be installed on the Hyper-V Server, and the execution policy for the local machine must be set to RemoteSigned. By default, Windows Server 2008 R2 includes PowerShell 2.0, which you must update to 3.0 or later. Windows Server 2012, 2012 R2, and 2016 include 3.0, 4.0, and 5.0, respectively.
After you have installed it, run the following command from the PowerShell command prompt:
Set-ExecutionPolicy RemoteSigned
•
Install Integration Services: The Integration Services must be installed on the VM from the Hyper‑V Server. Integration Services are installed by default on Windows-based VMs.
•
Install NetVault Backup Server and Client software: At a minimum, the NetVault Backup Client software must be installed on the Hyper‑V Server. For instructions on installing the NetVault Backup Client software and adding the Hyper‑V Server as a Heterogeneous Client, see the Quest NetVault Backup Installation Guide.

Prerequisite for using SMB file servers

If the Hyper-V VMs that you back up using the plug-in reside on an SMB file server, verify that the following server roles are enabled. If not, use the Server Manager in Windows Server to add these roles.

 
Table 1. Required roles for use with VMs stored on SMB file servers
Name
Type
Path

File and Storage Services

Role

File and Storage Services

File and iSCSI Services

Role Service

File and Storage Services\File and iSCSI Services

File Server

Role Service

File and Storage Services\File and iSCSI Services\File Server

File Server VSS Agent Service

Role Service

File and Storage Services\File and iSCSI Services\File Server VSS Agent Service

Installing or upgrading the plug-in

The installation process depends on whether you are deploying the plug-in in a standalone or clustered environment:

•
Installing the plug-in in a standalone deployment
•
Installing the plug-in in a clustered deployment

Installing the plug-in in a standalone deployment

1
Access the NetVault Configuration Wizard or Manage Clients page.
 
* 
NOTE: If the selected clients are all the same type, you can use the configuration wizard to install the plug-in on multiple clients at the same time. When you select multiple clients, verify that the plug-in binary file is compatible with the OS and platforms of the target clients. From the Manage Clients page, you can only select one client for plug-in installation.
•
To access the NetVault Configuration Wizard page:
a
In the Navigation pane, click Guided Configuration.
b
On the NetVault Configuration Wizard page, click Install Plugins.
c
On the next page, select the applicable clients.
•
To access the Manage Clients page:
a
In the Navigation pane, click Manage Clients.
b
On the Manage Clients page, select the machine that contains the Hyper‑V Server, and click Manage.
c
On the View Client page, click the Install Plugin button ().
2
Click Choose Plug-in File, and navigate to the location of the “.npk” installation file for the plug-in — on the installation CD or the directory to which the file was downloaded from the website.
Based on the OS in use, the path for this software may vary on the installation CD.
3
Select the file entitled “hv-x-x-x-x-x.npk,” where xxxxx represents the version number and platform, and click Open.
4
To begin installation, click Install Plugin.
After the plug-in is successfully installed, a message is displayed.
Documents connexes

The document was helpful.

Sélectionner une évaluation

I easily found the information I needed.

Sélectionner une évaluation