Tchater maintenant avec le support
Tchattez avec un ingénieur du support

DR Series Software 3.2.0.2 - Administrator Guide

Introduction to the DR Series System Documentation Understanding the DR Series System Setting Up the DR Series System Hardware Configuring the DR Series System Settings Managing DR Series Storage Operations Monitoring the DR Series System Using Global View Using the DR Series System Support Options Configuring and Using Rapid NFS and Rapid CIFS Configuring and Using Rapid Data Access with Dell NetVault Backup and with Dell vRanger Configuring and Using RDA with OST
Understanding RDA with OST Guidelines Terminology Supported RDA with OST Software and Components Best Practices: RDA with OST and the DR Series System Setting Client-Side Optimization Configuring an LSU Installing the RDA with OST Plug-In Configuring DR Series System Information Using NetBackup Backing Up Data From a DR Series System (NetBackup) Using Backup Exec With a DR Series System (Windows) Understanding the OST CLI Commands Understanding RDA with OST Plug-In Diagnostic Logs Collecting Diagnostics Using a Linux Utility Guidelines for Gathering Media Server Information
Configuring and Using VTL Configuring and Using Encryption at Rest Troubleshooting and Maintenance Supported Ports in a DR Series System Getting Help
2.
Select a time range (if needed) and click Apply.
3.
Click the Protocols tab.
Under NFS Usage and CIFS Usage, there is an XWrite checkbox. This checkbox represents the accelerator activity.
4.
In the desired usage graph pane, select the XWritecheckbox to view the accelerator performance over time.

If you have Rapid NFS enabled, you can use the command line to view statistics, throughput, and the plug-in version by running the ru utility on the client, as follows:

ru --mpt=[rdnfs mount point] | --pid=[process ID of rdnfs] --show=[name|version|parameters|stats|performance]

If you have Rapid CIFS enabled, you can use the command line to view aggregate statistics (even while a backup job is running) using the following command:

\Program Files\Dell\Rapid CIFS\rdcifsctl.exe stats -s
Parent topic 

Uninstalling the Rapid NFS Plug-In

Uninstalling the Rapid NFS Plug-In

Use the following procedure to remove the Dell Rapid NFS plug-in from a Linux-based media server. After you uninstall the plug-in, Rapid NFS will be disabled and “inactive” will be shown next to NFS Write Accelerator on the NFS Connection Configuration pane on the Container Statistics page.

NOTE: Dell recommends that you retain the Dell Rapid NFS plug-in installer on the media server in case you need to use it to reinstall the plug-in. It is usually located in /opt/dell/DR-series/RDNFS/scripts.

To uninstall the Rapid NFS plug-in on Linux:

1.
Stop the Data Management Application (DMA) backup service before using the -uninstall option.
The Rapid NFS plug-in installer returns an error if the DMA service is running when attempting to uninstall the plug-in.
2.
Run the Rapid NFS plug-in installer (usually located in /opt/dell/DR-series/RDNFS/scripts) with the -uninstall option, which uninstalls the plug-in, using the following command:
$> ./DellRapidNFS-xxxxx-x86_64.bin -uninstall
 
NOTE: You must stop the DMA service before uninstalling the Rapid NFS plug-in (you are also required to use the Dell Rapid NFS plug-in installer to uninstall the plug-in).
3.
Check that the plug-in is uninstalled by viewing the usage graph in the GUI; it should not indicate any XWriteactivity.
Parent topic 

Uninstalling the Rapid CIFS Plug-In

Uninstalling the Rapid CIFS Plug-In

Use the following standard Microsoft Windows uninstall process to remove the Dell Rapid CIFS plug-in from a Windows-based media server. After you uninstall the plug-in, Rapid CIFS will be disabled and “inactive” will be shown next to CIFS Write Accelerator on the CIFS Connection Configuration pane on the Container Statisticspage.

Alternatively, if you want to disable (but not uninstall) the plug-in, you can run the following Rapid CIFS utility command. The utility is located in Program Files\Dell\Rapid CIFS.
 
NOTE: Dell recommends that you retain the Dell Rapid CIFS plug-in installer on the media server in case you need to use it to reinstall the plug-in.

To uninstall the Rapid CIFS plug-in on Windows:

1.
Click Start, and click Control Panel.
The Control Panel page is displayed.
2.
Under Programs and Features, click Uninstall a program.
The Uninstall or change a program page is displayed.
3.
Locate the Dell Rapid CIFS plug-in in the listed of installed programs, right click and select Uninstall.
The Programs and Features confirmation dialog is displayed.
4.
Click Yes to uninstall the Dell Rapid CIFS plug-in.
Parent topic 

Configuring and Using Rapid Data Access with Dell NetVault Backup and with Dell vRanger

Configuring and Using Rapid Data Access with Dell NetVault Backup and with Dell vRanger

Guidelines for using RDA with NetVault Backup and with vRanger
Best Practices: RDA with NetVault Backup and vRanger and the DR Series System
Setting Client-Side Optimization
Adding RDS Devices in NetVault Backup
Removing RDS Devices From NetVault Backup
Backing Up Data on the RDS Container Using NetVault Backup
Replicating Data to a RDS Container using NetVault Backup
Restoring Data From a DR Series System using NetVault Backup
Supported DR Series System CLI Commands for RDS
 
 
Documents connexes

The document was helpful.

Sélectionner une évaluation

I easily found the information I needed.

Sélectionner une évaluation