Archive Manager for Exchange 8.7 - Auditing Guide

Configure Database

In this topic:

·Steps to configure the Auditing database

·Steps to install the Auditing database

·Steps to configure the connection setting

Steps to configure the Auditing database

1.When the installation completes, the Configuration wizard opens. If it does not open automatically, click Start > Metalogix > Archive Manager Configuration.

2.From the feature panel on the left, click HSM and select the Database tab.

3.Click Configure. The Database Connection Wizard opens.

4.Select either Microsoft SQL Server or Oracle and click Next. If you choose Microsost SQL Server, the Database Connection window opens for the Microsoft SQL Server connection information.

For Microsoft SQL Server

a.Server name - name of the SQL server (eg. AMXDB)

b.Initial catalog - name of the HSM database (e.g. MAMAUDIT which is the default name of the HSM database)

c.Schema name - name of the SQL Schema (e.g. dbo)

d.Authentication – authentication type used for the database. Choose either Windows authentication or SQL Server authentication

e.User name - database login user name if SQL Server authentication is the selected as the authentication mode.

f.Password - password of the database user if SQL Server authentication is the selected as the authentication mode.

For Oracle

a.Oracle net name - net service name that describes the network address of the database server in your tnsnames.ora file.

b.Schema - name of the Oracle schema from your tnsnames.ora file.

c.User name - database login user name.

d.Password -  password of the database user.

5.Click Next and then click Yes on the confirmation dialog that opens.

6.If the database connection is setup successfully, the configuration completion window opens.

7.Click Finish to close the Database Connection wizard.

Steps to install the Auditing database

1.From the feature panel on the left in the Configuration tool, click Auditing and then select the Database tab.

2.Verify that the database connection information is as expected. Then click Run Scripts.

3.Click Select All and then click Next. The script installer wizard opens.

4.Enter the following information:

a.Authentication - authentication type used for the database. Choose either Windows authentication or SQL Server authentication

a.Database user - database login user name if SQL Server authentication is the selected as the authentication mode.

b.Password - password of the database user if SQL Server authentication is the selected as the authentication mode.

c.I want to see the SQL script before it is run (for advanced users) - select this check box to review the SQL scripts.

5.Click Next.

6.If the I want to see the SQL script before it is run (for advanced users) check box was selected in the previous step the View SQL Scripts window opens.

7.Click Next or if the I want to see the SQL script before it is run (for advanced users) check box was not selected, the Run SQL Scripts window opens.

8.Click Next. to run the scripts.

9.Click Finish to close the script installer. The Scripts section of the Configuration tool displays the status and version of the scripts(the version of the scripts you install may differ from the version shown in the image below).

Steps to configure the connection setting

1.From the feature panel on the left in the Configuration tool, click Auditing and then select the Database tab.

Configure Log targets

In the Log targets tab you can configure multiple types of log targets. The default and mandatory log target is the log database. Other targets are optional, depending on administrator’s needs. Multiple log targets can be defined and their usage can be conditional. Logging events of different severity can be logged to different targets or entries containing a specific string can be omitted.

Steps to add a new log target

1.Click Add. The Add log target window opens.

Enter the information as described below:

a.Name - name of the log target.

b.Type - type of the log target. Choose from one of the following options:

·Debug Output - writes log entries into the debug output; it can be used only for debugging purposes, since it does not keep the entries

·Event log - writes log entries into the system event log; it is recommended to use this target for critical errors and events only

·File - writes log entries into the specified file

·Rolling File - Writes log entries into files and rolls log files based on size or date or both

·Net Send - sends log entries as network messages; it can be used for notification purposes in case of critical errors

·Email - sends log entries as e-mails; it can be used for notification purposes in case of critical errors

2.Click OK to add the new log target to the Log targets list view.

Steps to configure log targets

The target selected in the Log targets list can be configured in the Log target configuration section. You can configure it in the Log target configuration section. For each log target you can define:

·Threshold level

·Filters

·Layout (not applicable for database)

Additionally, every log target has its specific properties as described further.

Threshold Level

Threshold level specifies the threshold level for the selected log target. All logging events with lower level than the threshold level are ignored. If Off is selected, nothing will be logged for the selected target.

Filters

User can define a set of filters for each logging target. Filters form a chain that the logging event has to pass through. Any filter along the way can accept the event and stop processing, deny the event and stop processing, or allow the event on to the next filter. If the event gets to the end of the filter chain without being denied it is implicitly accepted and will be logged.

The available filter types are:

·StringMatchFilter – matches a string (or regular expression) in the rendered message

·PropertyMatchFilter – matches a string (or regular expression) in the value for a specific event property

·DenyAllFilter – this filter drops all logging events

To define a filter for a log target:

1.Select the log target in the Log targets list view.

2.In the Filters section click Edit.

3.In the Edit filters dialog double-click the filter type.

4.In the filters options specify filter settings.

5.Click Apply.

Example:

If you want to allow through only messages that have a specific substring (e.g. 'database') then you need to specify the following filters:

·StringMatchFilter, String to match: ‘database’, Accept on match: true

·DenyAllFilter

If you do not want to log events having substring ‘debug’, you need to specify the following filter:

·StringMatchFilter, String to match: ‘debug’, Accept on match: false

Layout

User can define the layout of a log entry (line) for log targets, except of the Auditing Database. The layout is the sequence of property values separated by arbitrary characters. The available properties are:

·Product – product generating the logging event

·Category – category of the logging event

·Level – level of the logging event

·Message – application supplied message associated with the logging event

·Method – method name where the logging request was issued

·Data – data associated with the logging event

·Computer – name of the computer where the logging request was issued

·User – name of the user generating the logging request

·Date – date of the logging event

·Newline – platform dependent line separator character or characters

Specific Log target Properties

Activate auditing

1.In the Archive Manager Administration Center, open Tools > Options > Server settings > Auditing.

2.Select the Activate Auditing check box.

3.In the Server Name enter the name of the machine where the Auditing feature is installed

4.Specify the Server Port or leave the default.

5.Click Apply.

Add audit users

As the default, only the super-user has auditing rights, i.e. only the super-user can browse the auditing logs in ArchiveWeb. If you want other users to have access to auditing logs in ArchiveWeb, specific auditing roles must be granted.

1.Log on to ArchiveWeb with the super-user credentials.

2.Click the logged on user name in the right upper corner. From the dropdown menu select Manage settings. Then click Roles on the grey sub-bar.

3.In the left pane select the server for which the roles should apply. Or select Global option. ArchiveWeb roles appear in the main pane. List of roles is split into sections – Exchange Archive features are listed under Exchange roles, search features under Search roles etc. The Auditing roles are listed at the end.

4.Select the Show auditing logs role. All users with this role are displayed under the list. In case the desired user is not visible, click the Add users and groups icon () to add it to the list. Then click Allow check mark.