立即与支持人员聊天
与支持团队交流

vRanger 7.6.6 - User Guide

Introduction Configuring vRanger
Configuring vRanger through the Startup Wizard Configuring vRanger manually Supplemental instructions: additional repository types
Using vRanger Backup Restore
Restoring a physical server Performing a full restore for VMware VMs Performing a full restore for Hyper-V® VMs Performing a full restore for VMware vApps Performing a full restore of a physical machine Performing an FLR on Windows Performing an FLR on Linux Restoring from manifest
Replicate VMs Reports Integrating and monitoring vRanger Using the vRanger Console vAPI Cmdlet details
Add-BackupJobTemplate Add-CIFSRepository Add-DdbReplicationRepository Add-DdbRepository Add-EsxHost Add-HypervCluster Add-HypervHost Add-HypervRestoreJobTemplate Add-NFSRepository Add-NVSDRepository Add-PhysicalMachine Add-RdaRepository Add-ReplicationJobTemplate Add-RestoreFromManifestJobTemplate Add-RestoreJobTemplate Add-VirtualAppforLinuxFLR Add-VirtualAppforLinuxFLRVA Add-VirtualCenter Disable-Job Dismount-LinuxVolume Enable-Job Get-AddressBook Get-BackupGroupEntity Get-CatalogSearchData Get-CatalogStatus Get-ConfigOption Get-Connection Get-CurrentTemplateVersionID Get-Datastore Get-GlobalTransportFailover Get-InventoryEntities Get-IsInventoryRefreshing Get-Job Get-JobTemplate Get-MonitorLog Get-Network Get-PhysicalMachineDiskMap Get-Repository Get-RepositoryJob Get-RepositorySavePoint Get-RestoreDiskMap Get-SavepointDisk Get-SavepointManifest Get-Savepoints Get-TransportFailover Get-VirtualApplianceConfig Get-VirtualApplianceDeploymentStatus Get-VirtualApplianceReconfigStatus Get-VirtualMachinesUnderInventory Get-VmDisk Get-VMDKVolume Install-VirtualAppliance Mount-LinuxVolume New-BackupFlag New-BackupGroupMember New-Daily Schedule New-EmailAddress New-IntervalSchedule New-MonthlySchedule New-ReplicationFlag New-RestoreFlag New-SMTPServer New-TransportConfiguration New-VirtualAppliance New-WeeklySchedule New-YearlySchedule Remove-AllMount Remove-BackupGroupEntity Remove-BackupGroupMember Remove-Catalog Remove-DdbStorageUnit Remove-JobTemplate Remove-LinuxVolume Remove-Repository Remove-SavePoint Remove-VirtualAppliance Remove-VirtualApplianceConfiguration Run-JobsNow Run-ReplicationFailover Run-ResumeReplicationFailover Run-TestReplicationFailover Set-Cataloging Set-CBTonVM Set-LinuxVolume Set-MountPath Set-Resources Stop-vRangerJob Update-BackupJobTemplate Update-GlobalTransportFailover Update-HypervRestoreJobTemplate Update-Inventory Update-ReplicationJobTemplate Update-RestoreJobTemplate Update-VirtualAppliance Update-VirtualApplianceConfiguration
About us

Configuring VA networking

Previous Next



Configuring VA networking

If you have deployed one or more VAs using a static IP configuration, and you need to change that configuration after deployment, you must do so from within the VA.

To configure VA networking, complete the following tasks:

Logging in to the VA

Previous Next



Logging in to the VA

Complete the steps in the following procedure to log in to the VA.

To log in to the VA:
2
Using the console, log in as root to the VA, using the following default credentials:

If you supplied your own password during the VA deployment, use that password.

Changing the hostname

Previous Next



Changing the hostname

Complete the steps in the following procedure to change hostname.

To change the hostname:
4
Restart the VM by typing reboot at the prompt.

Changing the network configuration

Previous Next



Changing the network configuration

Optionally, you can complete the steps in the following procedure to change the network configuration.

To change the network configuration:

The following text is shown as an example:

GATEWAY=<IP of gateway>
PREFIX=<this entry is the subnet mask — your values may differ>
BROADCAST=<your broadcast IP — the highest IP in the VA’s subnet.>
5
Restart the VM by typing reboot at the prompt.
相关文档

The document was helpful.

选择评级

I easily found the information I needed.

选择评级