サポートと今すぐチャット
サポートとのチャット

vRanger 7.8.3 - Integration Guide for DR Series Disk Backup Appliance

Quest® vRanger® 7.8.3

Quest� vRanger� 7.8.3

Integration Guide for Quest� DR Series Disk Backup Appliance

© 2021 Quest Software Inc.

ALL RIGHTS RESERVED.

This guide contains proprietary information protected by copyright. The software described in this guide is furnished under a software license or nondisclosure agreement. This software may be used or copied only in accordance with the terms of the applicable agreement. No part of this guide may be reproduced or transmitted in any form or by any means, electronic or mechanical, including photocopying and recording for any purpose other than the purchaser’s personal use without the written permission of Quest Software Inc.

The information in this document is provided in connection with Quest Software products. No license, express or implied, by estoppel or otherwise, to any intellectual property right is granted by this document or in connection with the sale of Quest Software products. EXCEPT AS SET FORTH IN THE TERMS AND CONDITIONS AS SPECIFIED IN THE LICENSE AGREEMENT FOR THIS PRODUCT, QUEST SOFTWARE ASSUMES NO LIABILITY WHATSOEVER AND DISCLAIMS ANY EXPRESS, IMPLIED OR STATUTORY WARRANTY RELATING TO ITS PRODUCTS INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR NON-INFRINGEMENT. IN NO EVENT SHALL QUEST SOFTWARE BE LIABLE FOR ANY DIRECT, INDIRECT, CONSEQUENTIAL, PUNITIVE, SPECIAL OR INCIDENTAL DAMAGES (INCLUDING, WITHOUT LIMITATION, DAMAGES FOR LOSS OF PROFITS, BUSINESS INTERRUPTION OR LOSS OF INFORMATION) ARISING OUT OF THE USE OR INABILITY TO USE THIS DOCUMENT, EVEN IF QUEST SOFTWARE HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Quest Software makes no representations or warranties with respect to the accuracy or completeness of the contents of this document and reserves the right to make changes to specifications and product descriptions at any time without notice. Quest Software does not make any commitment to update the information contained in this document.

If you have any questions regarding your potential use of this material, contact:

Quest Software Inc.
Attn: LEGAL Dept.
4 Polaris Way
Aliso Viejo, CA 92656

Refer to our website (https://www.quest.com) for regional and international office information.

Patents

Quest Software is proud of our advanced technology. Patents and pending patents may apply to this product. For the most current information about applicable patents for this product, please visit our website at https://www.quest.com/legal.

Trademarks

Quest, the Quest logo, Foglight, NetVault, vRanger, and Join the Innovation are trademarks and registered trademarks of Quest Software Inc. vCenter, vSphere, vMotion, VMware, and ESXi are registered trademarks or trademarks of VMware, Inc. in the United States and/or other jurisdictions. Active Directory, Hyper-V, SharePoint, SQL Server, Windows, and Windows Server are registered trademarks of Microsoft Corporation in the United States and/or other countries. Data Domain and DD Boost are trademarks or registered trademarks of EMC Corporation in the United States and other countries. For a complete list of Quest marks, visit https://www.quest.com/legal/trademark-information.aspx. All other trademarks and registered trademarks are property of their respective owners.

Legend


WARNING: A WARNING icon indicates a potential for property damage, personal injury, or death.




CAUTION: A CAUTION icon indicates potential damage to hardware or loss of data if instructions are not followed.




IMPORTANT NOTE, NOTE, TIP, MOBILE, or VIDEO: An information icon indicates supporting information.


vRanger Integration Guide for Quest� DR Series Disk Backup Appliance
Updated - August 2021
Software Version - 7.8.3

Getting started

Getting started

•    vRanger integration quick start for Quest� DR Series

•    Product overviews


IMPORTANT: The information in this topic is intended only to provide an overview of the steps and information required to configure vRanger and the Quest DR Series appliance. Before implementing this solution, review the full vRanger and Quest DR Series documentation.


vRanger integration quick start for Quest DR Series

Integrating vRanger with a Quest DR Series appliance is achieved by adding the DR Series appliance to vRanger as a Quest Rapid Data Access (RDA) repository. The following steps describe the integration process at a high level, and provide links to the remaining topics for more exploration. Before implementing this solution in a production environment, read this information thoroughly.

1    Confirm integration requirements: Before starting the integration, confirm that you are using supported versions of vRanger and the DR Series software. For more information, see Product requirements for integration.

2    Install and configure the DR Series: To install your DR Series and integrate with vRanger, perform the following operations:

▪    Install the DR Series hardware: Assemble the rails, and install and connect the DR Series to your infrastructure.

▪    Log in and initialize the DR Series: Log in to the DR Series system CLI by using a local console keyboard-video-mouse (KVM) connection or an iDRAC connection. Configure your system network settings using the Initial System Configuration Wizard.

▪    Configure network settings: Ensure that you have an active network connection and a fully configured IP address.

▪    Register and configure your DR Series: Log in to the web interface and complete the registration process and Initial System Configuration Wizard, which includes password administration, Active Directory connection, and additional network configuration.

▪    Create a storage container: Containers function like a shared file system, which can be assigned a connection type of None (to be defined later), NFS/CIFS, or RDA (includes Rapid Data Storage [RDS] clients). Containers can then be accessed using Network File System (NFS), Common Internet File System (CIFS), or RDA.


IMPORTANT: For integration with vRanger, create an RDA container, with the RDA Type setting as RDS.


3    Install vRanger: Using the vRanger installer, install vRanger on a machine meeting the vRanger system requirements. For a high-level overview of the vRanger installation process, see Installing vRanger. For more information, see the Quest vRanger Installation/Upgrade Guide.

4    Create a Quest RDA repository: After vRanger is installed, add the DR Series to vRanger as a Quest RDA repository. Any backup written to this repository is deduplicated according to your DR Series configuration.

Product requirements for integration

To integrate vRanger with a DR Series appliance, you must be using one of the following supported product versions:

•    vRanger:

▪    7.1 or later — for RDA integration

▪    7.0 — for CIFS/NFS only

•    DR Series systems:

▪    DR4x00

▪    DR6x00

•    DR Series software:

▪    4.0.3 or later — for RDA integration

▪    4.0.3 or later — for CIFS/NFS only

Product overviews

The following topics provide an overview of vRanger and the Quest DR Series appliances, and important information about the licensing required to integrate the two products.

What is vRanger?

vRanger is the leading VMware data protection solution that also backs up and recovers Windows physical servers and files with blazing speed and minimal storage requirements. With vRanger, you get comprehensive protection for both virtual and physical environments that you can manage from one intuitive interface.

vRanger has historically supported the Quest DR Series systems as repositories, but required that the Quest DR Series system was configured as an NFS share. vRanger extends this functionality to support the more advanced functionality offered by the DR Series, and allow direct configuration of Quest RDA repositories.

vRanger licensing

For virtual machine (VM) backup, a license for vRanger controls the number of source CPUs that you can configure for backup. For licensing purposes, a multi-core processor is counted as a single CPU. For physical backup, each server protected consumes one physical backup license.

Every VMware ESXi host for which vRanger is expected to provide protection must be properly licensed, both by VMware and in the vRanger Host Licensing tab.


IMPORTANT: A Quest vRanger license is required for integration with the Quest DR Series. vRanger Standard Edition (SE) and vReplicator are not supported by Quest DR Series. This topic uses “vRanger” for simplicity, but only vRanger Backup & Replication is supported for use with Quest DR Series.


Quest DR Series overview

The DR Series system is a high-performance, disk-based backup and recovery appliance that is simple to deploy and manage, and offers unsurpassed Total Cost of Ownership benefits. Features such as innovative firmware and an all-inclusive licensing model ensure optimal functionality and the assurance of no hidden costs for desired future features.

Using Quest deduplication and compression algorithm technology, this system can achieve data reduction levels averaging 15:1. This reduction in data results in less incremental storage needs and a smaller backup footprint. By removing redundant data, the system provides deduplication and compression that delivers:

•    Fast, reliable backup and restore functionality.

•    Reduces media usage and power and cooling requirements.

•    Improves overall data protection and retention costs.

•    Reduces overall network traffic — as only unique data is transmitted.

•    Allows for increased scalability through the addition of more RDA capable devices.

The benefits of data deduplication can be extended across the enterprise — through the deduplicated replication function — to provide a complete backup solution for multi-site environments.

Shorter Recovery Time Objectives (RTO) and more attainable Recovery Point Objectives (RPO) can be assured as critical backup data remains on disk and online longer. Capital and administrative costs are diminished at the same time as internal service-level agreements (SLAs) are more easily met.

The DR Series includes the following:

•    Advanced data protection and disaster recovery.

•    Simple management interface — using the system GUI.

•    Wide variety of data backup installations and environments.

The Quest DR Series contains data backup and management software preinstalled on a Quest hardware appliance, which provides you with a robust disk-based data backup capability installed on a deduplication-enabled appliance.

The system supports two interface types, and the system software manages the storage containers using the following interfaces:

•    A command line interface (CLI)

•    A graphical user interface (GUI)


vRanger integration quick start for Quest® DR Series

Getting started

•    vRanger integration quick start for Quest� DR Series

•    Product overviews


IMPORTANT: The information in this topic is intended only to provide an overview of the steps and information required to configure vRanger and the Quest DR Series appliance. Before implementing this solution, review the full vRanger and Quest DR Series documentation.


vRanger integration quick start for Quest DR Series

Integrating vRanger with a Quest DR Series appliance is achieved by adding the DR Series appliance to vRanger as a Quest Rapid Data Access (RDA) repository. The following steps describe the integration process at a high level, and provide links to the remaining topics for more exploration. Before implementing this solution in a production environment, read this information thoroughly.

1    Confirm integration requirements: Before starting the integration, confirm that you are using supported versions of vRanger and the DR Series software. For more information, see Product requirements for integration.

2    Install and configure the DR Series: To install your DR Series and integrate with vRanger, perform the following operations:

▪    Install the DR Series hardware: Assemble the rails, and install and connect the DR Series to your infrastructure.

▪    Log in and initialize the DR Series: Log in to the DR Series system CLI by using a local console keyboard-video-mouse (KVM) connection or an iDRAC connection. Configure your system network settings using the Initial System Configuration Wizard.

▪    Configure network settings: Ensure that you have an active network connection and a fully configured IP address.

▪    Register and configure your DR Series: Log in to the web interface and complete the registration process and Initial System Configuration Wizard, which includes password administration, Active Directory connection, and additional network configuration.

▪    Create a storage container: Containers function like a shared file system, which can be assigned a connection type of None (to be defined later), NFS/CIFS, or RDA (includes Rapid Data Storage [RDS] clients). Containers can then be accessed using Network File System (NFS), Common Internet File System (CIFS), or RDA.


IMPORTANT: For integration with vRanger, create an RDA container, with the RDA Type setting as RDS.


3    Install vRanger: Using the vRanger installer, install vRanger on a machine meeting the vRanger system requirements. For a high-level overview of the vRanger installation process, see Installing vRanger. For more information, see the Quest vRanger Installation/Upgrade Guide.

4    Create a Quest RDA repository: After vRanger is installed, add the DR Series to vRanger as a Quest RDA repository. Any backup written to this repository is deduplicated according to your DR Series configuration.

Product requirements for integration

To integrate vRanger with a DR Series appliance, you must be using one of the following supported product versions:

•    vRanger:

▪    7.1 or later — for RDA integration

▪    7.0 — for CIFS/NFS only

•    DR Series systems:

▪    DR4x00

▪    DR6x00

•    DR Series software:

▪    4.0.3 or later — for RDA integration

▪    4.0.3 or later — for CIFS/NFS only

Product overviews

The following topics provide an overview of vRanger and the Quest DR Series appliances, and important information about the licensing required to integrate the two products.

What is vRanger?

vRanger is the leading VMware data protection solution that also backs up and recovers Windows physical servers and files with blazing speed and minimal storage requirements. With vRanger, you get comprehensive protection for both virtual and physical environments that you can manage from one intuitive interface.

vRanger has historically supported the Quest DR Series systems as repositories, but required that the Quest DR Series system was configured as an NFS share. vRanger extends this functionality to support the more advanced functionality offered by the DR Series, and allow direct configuration of Quest RDA repositories.

vRanger licensing

For virtual machine (VM) backup, a license for vRanger controls the number of source CPUs that you can configure for backup. For licensing purposes, a multi-core processor is counted as a single CPU. For physical backup, each server protected consumes one physical backup license.

Every VMware ESXi host for which vRanger is expected to provide protection must be properly licensed, both by VMware and in the vRanger Host Licensing tab.


IMPORTANT: A Quest vRanger license is required for integration with the Quest DR Series. vRanger Standard Edition (SE) and vReplicator are not supported by Quest DR Series. This topic uses “vRanger” for simplicity, but only vRanger Backup & Replication is supported for use with Quest DR Series.


Quest DR Series overview

The DR Series system is a high-performance, disk-based backup and recovery appliance that is simple to deploy and manage, and offers unsurpassed Total Cost of Ownership benefits. Features such as innovative firmware and an all-inclusive licensing model ensure optimal functionality and the assurance of no hidden costs for desired future features.

Using Quest deduplication and compression algorithm technology, this system can achieve data reduction levels averaging 15:1. This reduction in data results in less incremental storage needs and a smaller backup footprint. By removing redundant data, the system provides deduplication and compression that delivers:

•    Fast, reliable backup and restore functionality.

•    Reduces media usage and power and cooling requirements.

•    Improves overall data protection and retention costs.

•    Reduces overall network traffic — as only unique data is transmitted.

•    Allows for increased scalability through the addition of more RDA capable devices.

The benefits of data deduplication can be extended across the enterprise — through the deduplicated replication function — to provide a complete backup solution for multi-site environments.

Shorter Recovery Time Objectives (RTO) and more attainable Recovery Point Objectives (RPO) can be assured as critical backup data remains on disk and online longer. Capital and administrative costs are diminished at the same time as internal service-level agreements (SLAs) are more easily met.

The DR Series includes the following:

•    Advanced data protection and disaster recovery.

•    Simple management interface — using the system GUI.

•    Wide variety of data backup installations and environments.

The Quest DR Series contains data backup and management software preinstalled on a Quest hardware appliance, which provides you with a robust disk-based data backup capability installed on a deduplication-enabled appliance.

The system supports two interface types, and the system software manages the storage containers using the following interfaces:

•    A command line interface (CLI)

•    A graphical user interface (GUI)


Product requirements for integration

Getting started

•    vRanger integration quick start for Quest� DR Series

•    Product overviews


IMPORTANT: The information in this topic is intended only to provide an overview of the steps and information required to configure vRanger and the Quest DR Series appliance. Before implementing this solution, review the full vRanger and Quest DR Series documentation.


vRanger integration quick start for Quest DR Series

Integrating vRanger with a Quest DR Series appliance is achieved by adding the DR Series appliance to vRanger as a Quest Rapid Data Access (RDA) repository. The following steps describe the integration process at a high level, and provide links to the remaining topics for more exploration. Before implementing this solution in a production environment, read this information thoroughly.

1    Confirm integration requirements: Before starting the integration, confirm that you are using supported versions of vRanger and the DR Series software. For more information, see Product requirements for integration.

2    Install and configure the DR Series: To install your DR Series and integrate with vRanger, perform the following operations:

▪    Install the DR Series hardware: Assemble the rails, and install and connect the DR Series to your infrastructure.

▪    Log in and initialize the DR Series: Log in to the DR Series system CLI by using a local console keyboard-video-mouse (KVM) connection or an iDRAC connection. Configure your system network settings using the Initial System Configuration Wizard.

▪    Configure network settings: Ensure that you have an active network connection and a fully configured IP address.

▪    Register and configure your DR Series: Log in to the web interface and complete the registration process and Initial System Configuration Wizard, which includes password administration, Active Directory connection, and additional network configuration.

▪    Create a storage container: Containers function like a shared file system, which can be assigned a connection type of None (to be defined later), NFS/CIFS, or RDA (includes Rapid Data Storage [RDS] clients). Containers can then be accessed using Network File System (NFS), Common Internet File System (CIFS), or RDA.


IMPORTANT: For integration with vRanger, create an RDA container, with the RDA Type setting as RDS.


3    Install vRanger: Using the vRanger installer, install vRanger on a machine meeting the vRanger system requirements. For a high-level overview of the vRanger installation process, see Installing vRanger. For more information, see the Quest vRanger Installation/Upgrade Guide.

4    Create a Quest RDA repository: After vRanger is installed, add the DR Series to vRanger as a Quest RDA repository. Any backup written to this repository is deduplicated according to your DR Series configuration.

Product requirements for integration

To integrate vRanger with a DR Series appliance, you must be using one of the following supported product versions:

•    vRanger:

▪    7.1 or later — for RDA integration

▪    7.0 — for CIFS/NFS only

•    DR Series systems:

▪    DR4x00

▪    DR6x00

•    DR Series software:

▪    4.0.3 or later — for RDA integration

▪    4.0.3 or later — for CIFS/NFS only

Product overviews

The following topics provide an overview of vRanger and the Quest DR Series appliances, and important information about the licensing required to integrate the two products.

What is vRanger?

vRanger is the leading VMware data protection solution that also backs up and recovers Windows physical servers and files with blazing speed and minimal storage requirements. With vRanger, you get comprehensive protection for both virtual and physical environments that you can manage from one intuitive interface.

vRanger has historically supported the Quest DR Series systems as repositories, but required that the Quest DR Series system was configured as an NFS share. vRanger extends this functionality to support the more advanced functionality offered by the DR Series, and allow direct configuration of Quest RDA repositories.

vRanger licensing

For virtual machine (VM) backup, a license for vRanger controls the number of source CPUs that you can configure for backup. For licensing purposes, a multi-core processor is counted as a single CPU. For physical backup, each server protected consumes one physical backup license.

Every VMware ESXi host for which vRanger is expected to provide protection must be properly licensed, both by VMware and in the vRanger Host Licensing tab.


IMPORTANT: A Quest vRanger license is required for integration with the Quest DR Series. vRanger Standard Edition (SE) and vReplicator are not supported by Quest DR Series. This topic uses “vRanger” for simplicity, but only vRanger Backup & Replication is supported for use with Quest DR Series.


Quest DR Series overview

The DR Series system is a high-performance, disk-based backup and recovery appliance that is simple to deploy and manage, and offers unsurpassed Total Cost of Ownership benefits. Features such as innovative firmware and an all-inclusive licensing model ensure optimal functionality and the assurance of no hidden costs for desired future features.

Using Quest deduplication and compression algorithm technology, this system can achieve data reduction levels averaging 15:1. This reduction in data results in less incremental storage needs and a smaller backup footprint. By removing redundant data, the system provides deduplication and compression that delivers:

•    Fast, reliable backup and restore functionality.

•    Reduces media usage and power and cooling requirements.

•    Improves overall data protection and retention costs.

•    Reduces overall network traffic — as only unique data is transmitted.

•    Allows for increased scalability through the addition of more RDA capable devices.

The benefits of data deduplication can be extended across the enterprise — through the deduplicated replication function — to provide a complete backup solution for multi-site environments.

Shorter Recovery Time Objectives (RTO) and more attainable Recovery Point Objectives (RPO) can be assured as critical backup data remains on disk and online longer. Capital and administrative costs are diminished at the same time as internal service-level agreements (SLAs) are more easily met.

The DR Series includes the following:

•    Advanced data protection and disaster recovery.

•    Simple management interface — using the system GUI.

•    Wide variety of data backup installations and environments.

The Quest DR Series contains data backup and management software preinstalled on a Quest hardware appliance, which provides you with a robust disk-based data backup capability installed on a deduplication-enabled appliance.

The system supports two interface types, and the system software manages the storage containers using the following interfaces:

•    A command line interface (CLI)

•    A graphical user interface (GUI)


セルフ・サービス・ツール
ナレッジベース
通知および警告
製品別サポート
ソフトウェアのダウンロード
技術文書
ユーザーフォーラム
ビデオチュートリアル
RSSフィード
お問い合わせ
ライセンスアシスタンス の取得
Technical Support
すべて表示
関連ドキュメント

The document was helpful.

評価を選択

I easily found the information I needed.

評価を選択