DR Series Software 4.0.3 - Command Line Reference Guide

サポートと今すぐチャット

Alerts Command Usage alerts --show [--email] alerts --show [--snmp] alerts --show [--events] [--index <[-]number> [--count <number>] [--all] alerts --show [--alerts] [--index <[-] number>] [--count <number>] [--all] alerts --show [--summary] alerts --email [--relay_host <server name>] alerts --email [--appliance_alerts <yes | no>] alerts --email [--software_updates <yes | no>] alerts --email [--daily_report <yes | no>] alerts --email [--daily_report_time <0–24 hr>] alerts --email [--sender_email <email address>] alerts --test_email alerts --snmp_add --host <server name> --port <number> --community <name> alerts --snmp_delete --host <server name> alerts --snmp_disable --host <server name> alerts --snmp_enable --host <server name> alerts --snmp_trap_email [--enable] [--disable] alerts --help

Authenticate Commands

Authenticate Command Usage authenticate --show [--users] authenticate --show [--domain <domain name>] authenticate --show [--login_group] authenticate --join --domain <domain name> [--ou <org-unit name>] --user <user name> authenticate --leave [--user <user name>] [--force] authenticate --update --kerberos authenticate --add [--user <user name>] authenticate --add [--login_group <DOMAIN\LOGIN GROUP>] authenticate --delete--user <user name> authenticate --delete [--login_group <DOMAIN\LOGIN GROUP>] authenticate --set --user <user name> authenticate --guestmode [--enable] [--disable] authenticate --guestmode [--enable] authenticate --guestmode [--disable] authenticate --server_signing --mode <auto | mandatory | disabled> authenticate --help

Network

Network Command Usage network --show network --delete network --restart network --setdhcp network --setstatic_ip [--bondif <bondN>] [--nwif <ethN>] --ip <IPv4/IPv6 address not already in use> --netmask <netmask> [--gateway <IPv4/IPv6 address>] network --create_bond network --create_eth network --add_member network --setdns [--suffix <dns suffix>] [--primary <IPv4/IPv6 address>] [--secondary <IPv4/IPv6 address>] network --setbonding --bondif <bondN> [--mode <ALB | 802.3ad>] [--mtu <supported MTU range 512 - 9000>] network --update network --factory_reset network --host network --route network --nslookup --destination <ip address | hostname> network --traceroute --destination <ip address | hostname> network --ping --destination <ip address | hostname> [--tries <number>] [--size <number>] [--interface <bondN | ethN>] network --blink network --enable network --troubleshoot [--links] [--gateway] [--ntp] [--dns] [--active_domain] [--nis] [--clients] [--port_mapper] [--network_config] [--show_active <NFS|CIFS|OST|RDS|NDMP|ISCSI|FC>] [--interface <bondN | ethN>] network --troubleshoot --gateway --interface <bondN | ethN> network --troubleshoot [--show_active <NFS| CIFS|OST|NDMP|ISCSI|RDS>] network --tcpdump [--port <nfs | windows | replication | ost | rds>] [--pkt_size <128 - 32768>] [--file_size <0 - 100>] [--stop] [--host <ip address list>] [--interface <bondN | ethN>] network --tcpdump [--pkt_size <128 - 32768>] network --tcpdump [--file_size <0 - 100>] network --tcpdump [--host <ip address list>] network --tcpdump [--port <nfs | windows | replication | ost | rds>] network --iperf_client --server <ip address | hostname> [--port <number>] [--window_size <num bytes [KB/MB]>] [--interval <num seconds>] [--time <num seconds>] network --iperf_server [--port <number>] [--window_size <num bytes [KB/MB>] network --help

OST

OST Command Usage ost --show [--config] [--file_history] [--name <name>] [--active_files] [--name <name>] [--clients] [--limits] ost --update --opdup_encryption <none | aes128 | aes256> ost --delete_client --name <OST Client Hostname> ost --update_client --name <OST Client Hostname> --mode <auto | passthrough | dedupe> ost --limit --speed <<num><KBps | MBps | GBps | default> --target <ip address | hostname> ost --partial_images --containerid <Container id> [--delete <Partial image path>] [--timeout <> 0>] ost --help

RDA

RDA Command Usage rda --show [--config] [--file_history] [--name <name>] [--active_files] [--name <name>] [--clients] [--limits] rda --update --opdup_encryption <none | aes128 | aes256> rda --delete_client --name <RDA Client Hostname> rda --update_client --name <RDA Client Hostname> --mode <auto| passthrough| dedupe> rda --limit --speed <<num><KBps| MBps| GBps> | default> --target <ip address | hostname> rda --partial_images --containerid <Container id> [--delete <Partial image path>] [--timeout <> 0>] rda --help

Stats

Stats Command Usage stats --system stats --cpu stats --memory stats --network stats --datacheck stats --nfs stats --cifs stats --ost stats --rds stats --ndmp stats --ndmp_completed stats --iscsi [--verbose] stats --fc [--iostat] [--linkstat] stats --container --name <name> stats --storage_group --name <name> stats --replication [--name <name>] stats --cleaner stats --clients [--type <NFS|CIFS|OST|RDS|NDMP|ISCSI|FC>] stats --reset [--nfs] [--cifs] [--ost] [--rds] [--datacheck] stats --reset --datacheck stats --seed stats --help stats --datacheck stats --datacheck Command Usage stats --help datacheck

Storage Group commands

Storage Group Command Usage storage_group --show [--name <name>] [--verbose] storage_group --add --name <name> [--compression_mode <fast|best>] storage_group --update --name <name> [--compression_mode <fast|best>] storage_group --encryption --name <name> [--set <ON | OFF>] [--mode <static|internal> <--interval <7 days to 70 years>] storage_group --setpassphrase --name <name> storage_group --delete --name <name> storage_group --help

System

System Command Usage system --show [--config] system --show [--hardware] system --show [--storage] [--type <boot | internal | external>] [--service_tag <service tag>] system --show [--storage] system --show [--license] [--verbose] system --show [--ntp] system --show [--version] system --show [--timezones [Region]] system --show [--upgradefile] system --show [--upgradehistory] system --show [--marker] system --show [--replication_traffic] system --show [--opdup_traffic] system --show [--backup_traffic] system --show [--mgmt_traffic] system --init system --init --secure_erase <1–pass/3-passes/7-passes> system --reboot system --shutdown system --upgrade system --license [--validate] [--add] system --setname --name <node_name> system --setdate [--date <date>] [--timezone <Region/Zone>] system --setntp [--add <server name>] system --setntp [--delete <server name>] system --setntp [--enable] system --setntp [--disable] system --setntp [--adjust_time] system --hybrid_replication [--enable][--disable][--status] system --rdairgap [--enable][--disable][--set_retention_period <0 days to 365 days>][--get_retention_period][--open][--close][--status] system --rdairgap_schedule [--start_time <HH:MM>][--end_time <HH:MM>][--remove] system --setlogin system --telnet [--enable | --disable] system --datacheck --enable system --datacheck --disable system --datacheck --throttle system --marker [--enable] [--disable] system --verify_on_read [--enable] [--disable] system --add_storage --enclosure <service tag> system --storage [--set_usage_alert <70% - 90%>] system --storage [--blink] [--type <internal | external>] [--service_tag <service tag>] [--disk <slot num>] system --storage [--unblink] [--type <internal | external>] [--service_tag <service tag>] [--disk <slot num> system --mgmt_traffic system --backup_traffic system --replication_traffic system --opdup_traffic system --help

User

Virtual Machine

Virtual Machine Command Usage virtual_machine -- show [--service_tag <service tag>] virtual_machine --show --summary virtual_machine --update [--host <ip address | hostname>] [--name <administrator name>] [--email <email address>] [--company <company name>] [--comments <comments>] virtual_machine --register [--host <ip address| hostname>] [--name <administrator name>] [--email <email address>] [--company <company name>] [--comments <comments>] virtual_machine --unregister [--force] virtual_machine –delete --service_tag <service tag>

Maintaining the DR Series System

Diagnostics

Maintenance

Managing DR Series System Storage Operations

System Storage Operation Commands Connection

Container

VTL

VTL Command Usage vtl --show [--name <name>] vtl --show --verbose [--name <name>] vtl --update_carts --name <name> --add --no_of_tapes <number> vtl --activate --name <name> [--force <yes|no>] vtl --deactivate --name <name> vtl --rescan --name <name> [--force <yes|no>] vtl --set_rw --name <name> [--id <number>] vtl --show_replstate --name <name> vtl --help

NDMP

NDMP Command Usage ndmp --show ndmp --update [--port <port number>] ndmp --help

iSCSI

ISCSI Command Usage iscsi --show [--user] iscsi --setpassword iscsi --sessions iscsi --help

FC Command Usage fc --show [--verbose] [--target] fc --sessions [--topology] [--condensed] fc --help <command>

Replication

Replication Command Usage replication --show [--name <name>] [--role <source | target>] [--verbose] [--limits] replication --show replication --show [--limits] replication --add --name <name> --role <source | target> --peer <ip address | hostname> [--peer_name <name>] [--peer_group_name <name>] [--replication_traffic <ip address | hostname>] [--encryption <none | aes128 | aes256>][--username <user name>] replication --update --name <name> --role <source | target> [--peer <ip address | hostname>] [--encryption <none | aes128 | aes256>] [--username <user name>] replication --delete --name <name> --role <source | target> [--force] replication --start --name <name> --role <source | target> replication --stop --name <name> --role <source | target> replication --limit --speed <<num><KBps | MBps | GBps> | default> --target <ip address | hostname> replication --resync --name <name> --role <source | target> replication --troubleshoot --peer <ip address | hostname> replication --help

Seed

Seed Command Usage seed --create --op <import | export> [--enc_type <aes128 | aes256>] [--storage_group_name <name>] seed --add_container --name <container name> seed --add_device --server <server name> --volume <volume> --username <username> --domain <domain name> seed --cleanup seed --remove_device seed --show seed --start seed --help

Schedule

Schedule Command Usage schedule --show [--cleaner] schedule --show [--replication] [--name <name>] schedule --add --day <day of the week> [--cleaner] [--replication] [--start_time <hh:mm>] [-- stop_time <hh:mm>] [--name <name>] schedule --delete --day <day of the week> [--cleaner] [--name <name>] [--replication] schedule --help

Data Integrity Checking

About Data Check

Priority Write Verify Scans Continuous Data Verification Scans Data Check CLI Commands Data Check Options

Data Check: Namespace Scan Option Data Check: Blockmap Scan Option Data Check: All Data Scan Option

System --Datacheck

System --Datacheck Command Usage system --datacheck system --datacheck --disable system --datacheck --enable system --datacheck --throttle system --help datacheck

stats --datacheck

stats --datacheck Command Usage stats --datacheck

Additional Linux Commands

grep more

About us

authenticate --guestmode [--disable]

NOTE: If you attempt to enable guestmode for all CIFS shares when the DR Series system is already joined to an ADS domain (using the DR Series system CLI authenticate --guestmode --enable command), the following error message displays: This node is already joined to domain <domainname>. Please leave the domain before enabling the guest-only mode.

authenticate --server_signing --mode <auto | mandatory | disabled>

authenticate --server_signing --mode <auto || disabled>

Description

Configures the server signing for Common Internet File System (CIFS) on a DR Series system. This is a security provision based on Server Message Block (SMB) signing, a form of packet authentication. After CIFS-based users are authenticated, SMB signing adds a digital signature to each packet that is transferred between client and server. These digital signatures verify that the identity of the server matches the credentials expected by the client, and vice versa. By verifying that every packet that is received comes from an authenticated source, these digital signatures ensure the integrity of the communications. The DR Series system CLI --server_signing --mode command contains four values:

•

auto — Configures authentication via server signing to be automatically performed.

•

mandatory — Configures authentication via server signing as mandatory, or the connection will be dropped.

•

disabled — Disables authentication via server signing so that no connections are accepted.

Syntax

authenticate --server_signing --mode auto

Result

Successfully added server signing to auto.

authenticate --help

Description

Displays the list of all authenticate-related options that can be used as a reference when using the DR Series system CLI.

Syntax

Result

Usage:
authenticate --show [--users]
[--domain <domain name>]
[--login_group]

authenticate --join --domain <domain name>
[--ou <org-unit name>]
--user <user name>

authenticate --leave [--user <user name>]
[--force]

authenticate --update --kerberos

authenticate --add [--user <user name>]
[--login_group <DOMAIN\LOGIN GROUP>]

authenticate --delete [--user <user name>]
[--login_group <DOMAIN\LOGIN GROUP>]

authenticate --set --user <user name>

authenticate --guestmode [--enable]
[--disable]

authenticate --server_signing --mode <auto|mandatory|disabled|show>

authenticate --help

authenticate <command> <command-arguments>
<command> can be one of:
--show Displays current ADS domain, authorized local CIFS users, and login group.
--join Joins an ADS domain.
--leave Leaves an ADS domain.
--update Updates ADS configuration.
--add Creates local workgroup user for CIFS authentication or adds login group.
--delete Deletes local workgroup user from CIFS authentication or deletes login group.
--set Sets password for a local workgroup user.
--guestmode Configures all CIFS shares for guest only access.
--server_signing Configures server signing for CIFS.

For command-specific help, please type authenticate --help <command>
For example:
authenticate --help show

Network

Network Command Usage

network --setstatic_ip [--bondif <bondN>] [--nwif <ethN>] --ip <IPv4/IPv6 address not already in use> --netmask <netmask> [--gateway <IPv4/IPv6 address>]

network --create_bond

network --create_eth

network --add_member

network --setdns [--suffix <dns suffix>] [--primary <IPv4/IPv6 address>] [--secondary <IPv4/IPv6 address>]

network --setbonding --bondif <bondN> [--mode <ALB | 802.3ad>] [--mtu <supported MTU range 512 - 9000>]

network --update

network --factory_reset

network --host

network --route

network --nslookup --destination <ip address | hostname>

network --traceroute --destination <ip address | hostname>

network --ping --destination <ip address | hostname> [--tries <number>] [--size <number>] [--interface <bondN | ethN>]

network --blink

network --enable

network --troubleshoot --gateway --interface <bondN | ethN>

network --tcpdump [--pkt_size <128 - 32768>]

network --tcpdump [--file_size <0 - 100>]

network --tcpdump [--host <ip address list>]

network --tcpdump [--port <nfs | windows | replication | ost | rds>]

network --iperf_client --server <ip address | hostname> [--port <number>] [--window_size <num bytes [KB/MB]>] [--interval <num seconds>] [--time <num seconds>]

network --iperf_server [--port <number>] [--window_size <num bytes [KB/MB>]

network --help

The DR Series system CLI commands let you perform the following network-related tasks:

•

Displays information about a DR Series system.

•

Deletes network interfaces.

•

Restarts networking.

•

Configures bond interface to use DHCP.

•

Assigns a static IP address to the bond interface.

•

Creates bond interfaces for the system.

•

Creates eth interfaces for the system.

•

Adds an interface to an existing bond.

•

Configures servers in the domain name system (DNS).

•

Updates the bonding mode or maximum transmission unit (MTU).

•

Updates bonding and individual interface information.

•

Resets networking to factory configuration.

•

Manages local hosts.

•

Manages local routes.

•

Looks up the IP address or hostname for a specific destination.

•

Starts a packet trace route for a specific network host.

•

Pings a destination host

•

Blinks LED on the specific ethernet device.

•

Starts the specific ethernet devices on restart.

•

Does not start the specific ethernet devices on restart.

•

Performs basic troubleshooting.

•

Capture network traffic.

•

Runs iperf (Network Performance) in client mode.

•

Runs iperf (Network Performance) in server mode.

製品を選択してください:

サービス向上のために、「Purpose of your Chat（チャットの目的）」を記入してください。

お客様の不具合に推奨されるソリューション

DR Series Software 4.0.3 - Command Line Reference Guide

authenticate --guestmode [--disable]

authenticate --server_signing --mode <auto | mandatory | disabled>

authenticate --help

Network