サポートと今すぐチャット
サポートとのチャット

DR Series Software 3.2.6 - Administrator Guide

Introduction to the DR Series System Documentation Understanding the DR Series System Setting Up the DR Series System Hardware Configuring the DR Series System Settings Managing DR Series Storage Operations Monitoring the DR Series System Using Global View Using the DR Series System Support Options Configuring and Using Rapid NFS and Rapid CIFS Configuring and Using Rapid Data Access with Dell NetVault Backup and with Dell vRanger Configuring and Using RDA with OST
Understanding RDA with OST Guidelines Terminology Supported RDA with OST Software and Components Best Practices: RDA with OST and the DR Series System Setting Client-Side Optimization Configuring an LSU Installing the RDA with OST Plug-In Configuring DR Series System Information Using NetBackup Backing Up Data From a DR Series System (NetBackup) Using Backup Exec With a DR Series System (Windows) Understanding the OST CLI Commands Understanding RDA with OST Plug-In Diagnostic Logs Collecting Diagnostics Using a Linux Utility Guidelines for Gathering Media Server Information
Configuring and Using VTL Configuring and Using Encryption at Rest Troubleshooting and Maintenance Supported Ports in a DR Series System Getting Help
$INSTALL_PATH\VERITAS\NetBackup\bin\bpdown.exe
2.
Run SETUP to install the plug-in.
3.
Check that the plug-in is installed by using the following NetBackup command on the Windows media server:
$INSTALL_PATH\VERITAS\NetBackup\bin\admincmd\bpstsinfo.exe -pi

This NetBackup command lists the plug-in details, as shown in the following example:

◦
Plug-In Name: libstspiDellMT.dll
◦
Prefix: DELL
◦
Label: OST Plug-in that interfaces with the DR Series system
◦
Build Version: 9
◦
Build Version Minor: 1
◦
Operating Version: 9
◦
Vendor Version: Dell OST plug-in 10.1
4.
Start the NetBackup services by using the following command:
$INSTALL_PATH\VERITAS\NetBackup\bin\bpup.exe
Parent topic 

Uninstalling the RDA with OST Plug-In for Windows

Uninstalling the RDA with OST Plug-In for Windows

Use the following process if you need to uninstall the RDA with OST plug-in from a Windows-based media server.

Use the standard Microsoft Windows uninstall process to uninstall the RDA with OST plug-in from a Windows-based media server.
NOTE: Dell recommends that you retain the RDA with OST plug-in installer on the media server in case you need to use it to reinstall the plug-in.
1.
Click Start, and click Control Panel.
The Control Panel page is displayed.
2.
Under Programs and Features, click Uninstall a program.
The Uninstall or change a program page is displayed.
3.
Locate the RDA with OST plug-in in the listed of installed programs, right-click and select Uninstall.
The Programs and Features confirmation dialog is displayed.
4.
Click Yes to uninstall the plug-in.
Parent topic 

Installing the RDA with OST Plug-In for NetBackup on Linux

Installing the RDA with OST Plug-In for NetBackup on Linux

This topic describes how to install the RDA with OST plug-in on a media server running the supported Red Hat Enterprise Linux or SUSE Linux server operating system software (using the NetBackup DMA).

Ensure that you have downloaded the RDA with OST plug-in installer into the correct directory on the designated media server. The plug-in installer is saved as DellOSTPlugin-xxxxx-x86_64.bin.gz, where xxxxx represents its build number.
Unzip the RDA with OST plug-in installer file using the following command:
$> /bin/gunzip DellOSTPlugin-xxxxx-x86_64.bin.gz
2.
Configure the executable bit on the plug-in installer using the following command:
$> /bin/chmod a+x DellOSTPlugin-xxxxx-x86_64.bin
3.
Stop the NetBackup nbrmms service before using the -install option.
The plug-in installer returns an error if the NetBackup nbrmms service is running when attempting to install the plug-in.
4.
Run the plug-in installer using the -install option, and install the plug-in using the following command:
$> ./DellOSTPlugin-xxxxx-x86_64.bin -install
 
NOTE: The location for installing the plug-in is not user-configurable.
5.
After the RDA with OST plug-in installer has stopped running, and the system prompt returns, verify that the plug-in has loaded properly by checking the output using the following NetBackup command on the Linux media server:
$> /usr/openv/netbackup/bin/admincmd/bpstsinfo -plugininfo

This NetBackup command lists the plug-in details as shown:

◦
Plug-In Name: libstspiDellMT.so
◦
Prefix: DELL
◦
Label: Dell OpenStorage (OST) Plug-in
◦
Build Version: 10
◦
Build Version Minor: 1
◦
Operating Version: 10
◦
Vendor Version: (EAR-2.0.0) Build: 41640
6.
Retain the plug-in installer on the media server so you can use it if needed to uninstall the plug-in.
Parent topic 

Uninstalling the RDA with OST Plug-In for Linux

Uninstalling the RDA with OST Plug-In for Linux

Use the following process if you need to uninstall the RDA with OST plug-in from a Linux-based media server:

Stop the NetBackup nbrmms service before using the -uninstall option.
(The plug-in installer returns an error if the NetBackup nbrmms service is running when attempting to uninstall the OST plug-in.)
2.
Run the RDA with OST plug-in installer with the -uninstall option, which uninstalls the plug-in, using the following command:
$> ./DellOSTPlugin-xxxxx-x86_64.bin -uninstall
3.
Check that the plug-in is uninstalled by using the following NetBackup command on the Linux media server:
$> /usr/openv/netbackup/bin/admincmd/bpstsinfo -plugininfo
 
NOTE: If the -pluginfo command returns any plug-in details, this means that the plug-in has not been uninstalled.
4.
Retain the plug-in installer on the media server in case you need to use it to reinstall the plug-in.
Parent topic 
関連ドキュメント

The document was helpful.

評価を選択

I easily found the information I needed.

評価を選択