DR Series Software 4.0.3.1 - Command Line Reference Guide

Tchater maintenant avec le support

Alerts Command Usage alerts --show [--email] alerts --show [--snmp] alerts --show [--events] [--index <[-]number> [--count <number>] [--all] alerts --show [--alerts] [--index <[-] number>] [--count <number>] [--all] alerts --show [--summary] alerts --email [--relay_host <server name>] alerts --email [--appliance_alerts <yes | no>] alerts --email [--software_updates <yes | no>] alerts --email [--daily_report <yes | no>] alerts --email [--daily_report_time <0–24 hr>] alerts --email [--sender_email <email address>] alerts --test_email alerts --snmp_add --host <server name> --port <number> --community <name> alerts --snmp_delete --host <server name> alerts --snmp_disable --host <server name> alerts --snmp_enable --host <server name> alerts --snmp_trap_email [--enable] [--disable] alerts --help

Authenticate Commands

Authenticate Command Usage authenticate --show [--users] authenticate --show [--domain <domain name>] authenticate --show [--login_group] authenticate --join --domain <domain name> [--ou <org-unit name>] --user <user name> authenticate --leave [--user <user name>] [--force] authenticate --update --kerberos authenticate --add [--user <user name>] authenticate --add [--login_group <DOMAIN\LOGIN GROUP>] authenticate --delete--user <user name> authenticate --delete [--login_group <DOMAIN\LOGIN GROUP>] authenticate --set --user <user name> authenticate --guestmode [--enable] [--disable] authenticate --guestmode [--enable] authenticate --guestmode [--disable] authenticate --server_signing --mode <auto | mandatory | disabled> authenticate --help

Network

Network Command Usage network --show network --delete network --restart network --setdhcp network --setstatic_ip [--bondif <bondN>] [--nwif <ethN>] --ip <IPv4/IPv6 address not already in use> --netmask <netmask> [--gateway <IPv4/IPv6 address>] network --create_bond network --create_eth network --add_member network --setdns [--suffix <dns suffix>] [--primary <IPv4/IPv6 address>] [--secondary <IPv4/IPv6 address>] network --setbonding --bondif <bondN> [--mode <ALB | 802.3ad>] [--mtu <supported MTU range 512 - 9000>] network --update network --factory_reset network --host network --route network --nslookup --destination <ip address | hostname> network --traceroute --destination <ip address | hostname> network --ping --destination <ip address | hostname> [--tries <number>] [--size <number>] [--interface <bondN | ethN>] network --blink network --enable network --troubleshoot [--links] [--gateway] [--ntp] [--dns] [--active_domain] [--nis] [--clients] [--port_mapper] [--network_config] [--show_active <NFS|CIFS|OST|RDS|NDMP|ISCSI|FC>] [--interface <bondN | ethN>] network --troubleshoot --gateway --interface <bondN | ethN> network --troubleshoot [--show_active <NFS| CIFS|OST|NDMP|ISCSI|RDS>] network --tcpdump [--port <nfs | windows | replication | ost | rds>] [--pkt_size <128 - 32768>] [--file_size <0 - 100>] [--stop] [--host <ip address list>] [--interface <bondN | ethN>] network --tcpdump [--pkt_size <128 - 32768>] network --tcpdump [--file_size <0 - 100>] network --tcpdump [--host <ip address list>] network --tcpdump [--port <nfs | windows | replication | ost | rds>] network --iperf_client --server <ip address | hostname> [--port <number>] [--window_size <num bytes [KB/MB]>] [--interval <num seconds>] [--time <num seconds>] network --iperf_server [--port <number>] [--window_size <num bytes [KB/MB>] network --help

OST

OST Command Usage ost --show [--config] [--file_history] [--name <name>] [--active_files] [--name <name>] [--clients] [--limits] ost --update --opdup_encryption <none | aes128 | aes256> ost --delete_client --name <OST Client Hostname> ost --update_client --name <OST Client Hostname> --mode <auto | passthrough | dedupe> ost --limit --speed <<num><KBps | MBps | GBps | default> --target <ip address | hostname> ost --partial_images --containerid <Container id> [--delete <Partial image path>] [--timeout <> 0>] ost --help

RDA

RDA Command Usage rda --show [--config] [--file_history] [--name <name>] [--active_files] [--name <name>] [--clients] [--limits] rda --update --opdup_encryption <none | aes128 | aes256> rda --delete_client --name <RDA Client Hostname> rda --update_client --name <RDA Client Hostname> --mode <auto| passthrough| dedupe> rda --limit --speed <<num><KBps| MBps| GBps> | default> --target <ip address | hostname> rda --partial_images --containerid <Container id> [--delete <Partial image path>] [--timeout <> 0>] rda --help

Stats

Stats Command Usage stats --system stats --cpu stats --memory stats --network stats --datacheck stats --nfs stats --cifs stats --ost stats --rds stats --ndmp stats --ndmp_completed stats --iscsi [--verbose] stats --fc [--iostat] [--linkstat] stats --container --name <name> stats --storage_group --name <name> stats --replication [--name <name>] stats --cleaner stats --clients [--type <NFS|CIFS|OST|RDS|NDMP|ISCSI|FC>] stats --reset [--nfs] [--cifs] [--ost] [--rds] [--datacheck] stats --reset --datacheck stats --seed stats --help stats --datacheck stats --datacheck Command Usage stats --help datacheck

Storage Group commands

Storage Group Command Usage storage_group --show [--name <name>] [--verbose] storage_group --add --name <name> [--compression_mode <fast|best>] storage_group --update --name <name> [--compression_mode <fast|best>] storage_group --encryption --name <name> [--set <ON | OFF>] [--mode <static|internal> <--interval <7 days to 70 years>] storage_group --setpassphrase --name <name> storage_group --delete --name <name> storage_group --help

System

System Command Usage system --show [--config] system --show [--hardware] system --show [--storage] [--type <boot | internal | external>] [--service_tag <service tag>] system --show [--storage] system --show [--license] [--verbose] system --show [--ntp] system --show [--version] system --show [--timezones [Region]] system --show [--upgradefile] system --show [--upgradehistory] system --show [--marker] system --show [--replication_traffic] system --show [--opdup_traffic] system --show [--backup_traffic] system --show [--mgmt_traffic] system --init system --init --secure_erase <1–pass/3-passes/7-passes> system --reboot system --shutdown system --upgrade system --license [--validate] [--add] system --setname --name <node_name> system --setdate [--date <date>] [--timezone <Region/Zone>] system --setntp [--add <server name>] system --setntp [--delete <server name>] system --setntp [--enable] system --setntp [--disable] system --setntp [--adjust_time] system --hybrid_replication [--enable][--disable][--status] system --rdairgap [--enable][--disable][--set_retention_period <0 days to 365 days>][--get_retention_period][--open][--close][--status] system --rdairgap_schedule [--start_time <HH:MM>][--end_time <HH:MM>][--remove] system --setlogin system --telnet [--enable | --disable] system --datacheck --enable system --datacheck --disable system --datacheck --throttle system --marker [--enable] [--disable] system --verify_on_read [--enable] [--disable] system --add_storage --enclosure <service tag> system --storage [--set_usage_alert <70% - 90%>] system --storage [--blink] [--type <internal | external>] [--service_tag <service tag>] [--disk <slot num>] system --storage [--unblink] [--type <internal | external>] [--service_tag <service tag>] [--disk <slot num> system --mgmt_traffic system --backup_traffic system --replication_traffic system --opdup_traffic system --help

User

Virtual Machine

Virtual Machine Command Usage virtual_machine -- show [--service_tag <service tag>] virtual_machine --show --summary virtual_machine --update [--host <ip address | hostname>] [--name <administrator name>] [--email <email address>] [--company <company name>] [--comments <comments>] virtual_machine --register [--host <ip address| hostname>] [--name <administrator name>] [--email <email address>] [--company <company name>] [--comments <comments>] virtual_machine --unregister [--force] virtual_machine –delete --service_tag <service tag>

Maintaining the DR Series System

Diagnostics

Maintenance

Managing DR Series System Storage Operations

System Storage Operation Commands Connection

Container

VTL

VTL Command Usage vtl --show [--name <name>] vtl --show --verbose [--name <name>] vtl --update_carts --name <name> --add --no_of_tapes <number> vtl --activate --name <name> [--force <yes|no>] vtl --deactivate --name <name> vtl --rescan --name <name> [--force <yes|no>] vtl --set_rw --name <name> [--id <number>] vtl --show_replstate --name <name> vtl --help

NDMP

NDMP Command Usage ndmp --show ndmp --update [--port <port number>] ndmp --help

iSCSI

ISCSI Command Usage iscsi --show [--user] iscsi --setpassword iscsi --sessions iscsi --help

FC Command Usage fc --show [--verbose] [--target] fc --sessions [--topology] [--condensed] fc --help <command>

Replication

Replication Command Usage replication --show [--name <name>] [--role <source | target>] [--verbose] [--limits] replication --show replication --show [--limits] replication --add --name <name> --role <source | target> --peer <ip address | hostname> [--peer_name <name>] [--peer_group_name <name>] [--replication_traffic <ip address | hostname>] [--encryption <none | aes128 | aes256>][--username <user name>] replication --update --name <name> --role <source | target> [--peer <ip address | hostname>] [--encryption <none | aes128 | aes256>] [--username <user name>] replication --delete --name <name> --role <source | target> [--force] replication --start --name <name> --role <source | target> replication --stop --name <name> --role <source | target> replication --limit --speed <<num><KBps | MBps | GBps> | default> --target <ip address | hostname> replication --resync --name <name> --role <source | target> replication --troubleshoot --peer <ip address | hostname> replication --help

Seed

Seed Command Usage seed --create --op <import | export> [--enc_type <aes128 | aes256>] [--storage_group_name <name>] seed --add_container --name <container name> seed --add_device --server <server name> --volume <volume> --username <username> --domain <domain name> seed --cleanup seed --remove_device seed --show seed --start seed --help

Schedule

Schedule Command Usage schedule --show [--cleaner] schedule --show [--replication] [--name <name>] schedule --add --day <day of the week> [--cleaner] [--replication] [--start_time <hh:mm>] [-- stop_time <hh:mm>] [--name <name>] schedule --delete --day <day of the week> [--cleaner] [--name <name>] [--replication] schedule --help

Data Integrity Checking

About Data Check

Priority Write Verify Scans Continuous Data Verification Scans Data Check CLI Commands Data Check Options

Data Check: Namespace Scan Option Data Check: Blockmap Scan Option Data Check: All Data Scan Option

System --Datacheck

System --Datacheck Command Usage system --datacheck system --datacheck --disable system --datacheck --enable system --datacheck --throttle system --help datacheck

stats --datacheck

stats --datacheck Command Usage stats --datacheck

Additional Linux Commands

grep more

About us

container --show

container --add --name <name> [--type <VTL>] [--tape_size <tape_size>][--no_of_drives <1–60>][--is_oem <yes|no>][--oem_vendor <QUEST|DELL>][--group_name <name>]

Description

Creates and names a new container in the DR Series system.

NOTE: Container names and storage group names cannot exceed 32 characters in length. The “_” character is allowed for no-VTL containers. Container names cannot start with a number, and the /, #, and @ special characters are not allowed. Valid values for the container and storage group name are [a-z, A-Z, 0–9, and ‘_’.

NOTE: When creating a VTL container type, you must specify the option, --type VTL. Possible values for tape size include:

NOTE: 800GB|400GB|200GB|100GB|50GB|10GB

NOTE: The number of drives parameter is applicable to FC containers only.

Syntax

container --add --name acme99

Result

Container "acme99" created successfully.

Syntax

container --add --name vtlcont --type vtl --is_oem yes --tape_size 100gb

Example 1. Result

Container "vtlcont" created successfully.

container --update --name <name> [--no_of_drives <1–60>]

Description

Updates the specified container with the specified number of drives. This is applicable to FC type containers only.

Syntax

container --update --name fc1 --no_of_drives 32

Result

The FC service will be restarted for this change to take effect, Do you want to continue? (yes/no) [n]? y
Successfully updated Container FC1's number of drives as 32.

Documents connexes

The document was helpful.

Sélectionner une évaluation

I easily found the information I needed.

Sélectionner une évaluation

Veuillez sélectionner votre produit

Afin de mieux répondre à vos besoins, précisez l'objet du tchat:

Solutions recommandées pour votre problème

DR Series Software 4.0.3.1 - Command Line Reference Guide

container --show

container --show [--name <name>] [--verbose]

container --add --name <name> [--type <VTL>] [--tape_size <tape_size>][--no_of_drives <1–60>][--is_oem <yes|no>][--oem_vendor <QUEST|DELL>][--group_name <name>]

container --update --name <name> [--no_of_drives <1–60>]