Tchater maintenant avec le support
Tchattez avec un ingénieur du support

DR Series Software 4.0.0.3 - Administration Guide

Introducing the DR Series system documentation Introducing the DR Series system Setting up the DR Series system Configuring the DR Series system settings Managing containers Managing replications Monitoring the DR Series system Using GlobalView Configuring and using Rapid NFS and Rapid CIFS Configuring and using Rapid Data Access with NetVault Backup and with vRanger Configuring and using RDA with OST
Understanding RDA with OST Guidelines Terminology Supported RDA with OST software and components Best Practices: RDA with OST and the DR Series System Setting client-side optimization Configuring an LSU Installing the RDA with OST plug-in Configuring DR Series system information using NetBackup Backing Up Data From a DR Series System (NetBackup) Using Backup Exec with a DR Series system (Windows) Understanding the OST CLI commands Understanding RDA with OST Plug-In Diagnostic Logs Collecting Diagnostics Using a Linux Utility Guidelines for Gathering Media Server Information
Configuring and using VTL Configuring and Using Encryption at Rest Support, maintenance, and troubleshooting Supported Ports in a DR Series System

Rebooting the DR Series system

Rebooting the DR Series system

If needed, you can reboot the DR Series system. To reboot your system, follow these steps:

1.
In the left navigation menu, click Support.
The Support page is displayed.
2.
In the Action menu in the upper right corner of the page, click Reboot.
3.
In the Confirmation dialog box, click Yes to proceed with rebooting the system.
Parent topic 

Shutting down the DR Series system

Shutting down the DR Series system

If needed, you can shut down the DR Series system in the DR Series system GUI..

 
CAUTION: You should fully understand what this action means to system operations before attempting to shut down the system. A system shutdown powers off the appliance on which the DR Series system software is installed. Once powered Off, you can only power it On again at its physical location, or you must use an iDRAC connection to the DR Series system.
 
NOTE: To shutdown the DR Series system using a UPS after a power loss, refer to the following article for information on how to do this using the shutdown command in the IPMI interface: http://www.dell.com/downloads/global/power/ps4q04-20040204-murphy.pdf.

To shutdown your DR Series system, complete the following:

1.
In the left navigation menu, click Support.
The Support page is displayed.
2.
In the Actions menu in the upper right corner of the page, click Shutdown.
3.
In the Confirmation dialog box, click Yes to proceed with shutting down the system.
Parent topic 

Viewing the software upgrade page

Viewing the software upgrade page

Upgrading the DR Series system software

On the Software Upgrade page you can view the currently installed version of the DR Series system software as well as the upgrade history. .

To view the Software Upgrade page, follow these steps.

1.
On the left navigation menu, click Support > Software Upgrade.

The Software Upgrade page is displayed.

2.
On this page you can view

the Current Version of the DR Series system software that is installed as well as the Upgrade History of previously installed software versions.

 
 
Parent topic 

Upgrading the DR Series system software

Upgrading the DR Series system software

You can obtain the latest DR Series system software binary package from the Quest website. You would then upload this file in the DR Series system GUI for the system software upgrade.

 
NOTE: The DR Series system only supports the copying of upgrade images and diagnostics files to and from the system using WinSCP. The DR Series system does not support the copying or deleting of any other file types using WinSCP. To use WinSCP to copy DR Series software upgrade and diagnostics log files, ensure that the File Protocol mode is set to SCP (Secure Copy) mode.
 
NOTE: You can use other SCP tools with the DR Series system, but you cannot use these other SCP tools to copy other types of files to or from the DR Series system.

To upgrade the DR Series system software, complete the following steps.

1.
Using your browser, go to support.quest.com/dr-series, select your specific DR model and then navigate to Software Downloads.
2.
Under Upgrade File, locate the version you want to download, and click the Download button. If you are not logged in, you may be prompted to log in with your registered Quest account.
3.
Save the latest system software upgrade file to a network location accessible by the DR Series system that is running the browser session started by the DR Series administrator.
4.
In the DR Series system GUI, in the left navigation menu, click Support > Software Upgrade.
The Software Upgrade page is displayed.
5.
Click the button, Select DR Binary Package.
6.
Browse to the location of the of the file you downloaded from quest.com, select the file, and click Open. The system verifies that the file is the proper format.
7.
Once the file has been uploaded, on the Software Upgrade page, click Start Upgrade.

The administrator who initiated the software upgrade sees a System Information pane that displays an alert and upgrade status, as well as the Current Version and Upgrade History versions of the DR Series system software listed.

The first time you log on after a software upgrade, you will see an Upgrade notification dialog box, which instructs you to review and verify user roles and logon information for your DR Series system and associated DMAs.

There are only three possible outcomes for a DR Series system software upgrade operation:

◦
Upgrade has completed successfully—no reboot is required.
◦
Upgrade has completed successfully—but a reboot is required (click Reboot in the Software Upgrade page).
◦
Upgrade has failed.
 
NOTE: If the DR Series system software upgrade operation fails, you can reboot the system and attempt another software upgrade operation using the DR Series system GUI. If this is unsuccessful, you can use the DR Series system CLI system --show command to view the current System State status. DR Series system software upgrades can also be performed using the DR Series system CLI. For details, see the DR Series System Command Line Reference Guide. If both the DR Series system GUI and CLI attempts are unsuccessful, contact Technical Support for assistance.
Parent topic 
Documents connexes

The document was helpful.

Sélectionner une évaluation

I easily found the information I needed.

Sélectionner une évaluation