Tchater maintenant avec le support
Tchattez avec un ingénieur du support

Recovery Manager for Exchange 5.8.6 - Release Notes

Product Licensing

When installing Recovery Manager for Exchange, you must specify a valid license file.

To specify a license file

  1. In the Setup Wizard, on the User Information page, click Browse.
  2. In the dialog box that opens, locate the Quest license file (*.dlv) and click Open.

For information about managing licenses, see the User Guide supplied with this release.

The Recovery Manager for Exchange license file contains a certain number of licenses for Exchange and Domino mailboxes and Personal Folders (.pst) files. Recovery Manager for Exchange allocates licenses from the installed license file to mailboxes or .pst files when you perform any of these actions:

  • Register an offline Exchange Server store or Lotus Domino database as a source storage, and then open that source storage in the Recovery Manager for Exchange user interface.

Recovery Manager for Exchange allocates licenses to all mailboxes the store or database includes. When you register the same store or database again (from another backup, for example), the mailboxes are recounted and their total number is updated with the new number of mailboxes held in the store or database being registered.

A primary mailbox and its associated archive mailbox are regarded as one mailbox.

  • Register an online Exchange mailbox as a source storage, and then open that source storage in the Recovery Manager for Exchange user interface.

Recovery Manager for Exchange allocates licenses to all online mailboxes in the on-premises or cloudbased Exchange organization to which the registered mailbox belongs.

A primary Exchange mailbox and its associated archive mailbox are regarded as one mailbox.

  • Register a Personal Folders (.pst) file as a source storage, and then open that source storage in the Recovery Manager for Exchange user interface.

When you have expended all licenses in the installed license file (that is, all licenses have been allocated to mailboxes or .pst files), to register new source storages you need to obtain and install a new license file holding a greater number of licenses. Note that you cannot revoke licenses allocated to mailboxes or .pst files.

Getting Started with Recovery Manager for Exchange

Getting Started with Recovery Manager for Exchange

Upgrade and installation instructions

To upgrade, install Recovery Manager for Exchange 5.8.6 on the computer where an earlier version of Recovery Manager for Exchange is installed. During the upgrade process, setup transfers the product configuration and backup registration information to the new installation. As a result, all source and target storages registered with the earlier version of Recovery Manager for Exchange are available in the product after upgrading.

For installation instructions, see the Recovery Manager for Exchange User Guide.

Additional resources

The Recovery Manager Community offers easy access to information and is a collaborative site where IT pros can ask questions and get answers. Interact with industry experts and your peers. Engage in discussions, browse through content, and more. So, make yourself at home:

https://www.quest.com/community/products/recovery-manager/f/forum

Globalization

This section contains information about installing and operating this product in non-English configurations, such as those needed by customers outside of North America. This section does not replace the materials about supported platforms and configurations found elsewhere in the product documentation.

This release is Unicode-enabled and supports any character set. It supports simultaneous operation with multilingual data. This release is targeted to support operations in the following regions: North America, Western Europe and Latin America, Central and Eastern Europe, Far-East Asia, Japan.

Third-Party Contributions

This product contains some third-party components (listed below). Copies of their licenses may be found at referencing https://www.quest.com/legal/license-agreements.aspx Source code for components marked with an asterisk (*) is available at http://opensource.quest.com.

Table 11: List of third-party contributions

Component License or acknowledgement
Active Directory Authentication Library 4.4.1 MIT

Copyright Notice - Active Directory Authentication Library 4.4.1 (C) Microsoft Corporation. All rights reserved.

ElasticSearch 1.6.1

Apache License Version 2.0, January 2004

This product includes software developed by the Apache Software Foundation (http://www.apache.org.)

Microsoft .NET Framework (x86, x64) 2.0 Microsoft Software Supplemental License
ZLib 1.1.4 zlib 1.2.3

Copyright ©1995-2005 Jean-loup Gailly and Mark Adler

ZLib.NET 1.0.3 ZLib.NET 1.0.3
Documents connexes

The document was helpful.

Sélectionner une évaluation

I easily found the information I needed.

Sélectionner une évaluation