Tchater maintenant avec le support
Tchattez avec un ingénieur du support

Foglight for DB2 (Cartridge) 5.9.7.23 - Release Notes

Required privileges

For information on the required privileges, refer to the Foglight for DB2 LUW Getting Started Guide.

Supported platforms

The operating system platforms and versions of DB2 that are supported for monitoring by Foglight for DB2 LUW are the following.

Supported DB2 versions

9.5, 9.7, 10.1, 10.5, 11.1, 11.5.

Supported Operating Systems

All operating systems supported by IBM.

Linux on IBM System z support

Foglight for DB2 LUW supports the monitoring of instances that are installed on Linux on System z. The supported monitored instance versions are the same as specified in the list above for the Linux platform.

* 
NOTE: IBM® DB2® pureScale is currently not supported for Linux on IBM System z.
HADR support

Foglight for DB2 LUW supports monitoring an environment configured to use HADR by creating agents to monitor each one of the nodes separately (applies for both primary nodes and secondary).

Physical partition

Foglight for DB2 LUW supports a physical partition. When monitoring a physical partition, ensure you create the agent using the agent installer on the coordinator host.

Workgroup edition

Foglight for DB2 LUW supports monitoring a workgroup edition instance.

OS Cluster support

Foglight for DB2 LUW supports monitoring an instance that is installed in an OS cluster environment.

To enable monitoring, follow the instructions on “Host connectivity settings” screen in the installation wizard:

•
Mark the “instance residing on an OS cluster”.
•
Make sure the virtual host name point to the virtual host name. This name will be used to install the DB2 agent and the IC agent.
pureScale support

Foglight for DB2 LUW supports monitoring a pureScale environment (except on Linux on IBM System z).

Troubleshooting

This section provides a list of references which address the most commonly faced issues relating to remote connectivity, allowing for easy troubleshooting using the vendor's information knowledge base:

•
To verify TCP/IP connectivity for SQL statement collections, Management Studio (SSMS) cannot be used as other protocols may be leveraged. Instead, verify connectivity using a UDL as detailed here: https://support.microsoft.com/kb/308075/.
•
To verify the WMI connectivity using a Microsoft Windows built-in utility, see https://technet.microsoft.com/en-us/library/cc180684.aspx.
•
To troubleshoot WMI access permissions, see http://blogs.technet.com/b/askperf/archive/2007/08/14/wmi-troubleshooting-permissions.aspx.
•
For information about WMI connectivity from Windows Server 2003/Vista and later versions, see http://msdn.microsoft.com/en-us/library/aa822854(VS.85).aspx.
•
For WMI troubleshooting tips and techniques, see http://msdn.microsoft.com/en-us/library/aa394603(VS.85).aspx.

Product licensing

Foglight includes a licensing capability that restricts access to those features that are defined in the license. Any Management Server installation requires a license that grants access to server-specific parts of the browser interface and the features associated with them. Foglight cartridges are also license-protected. While some cartridges are covered by the base Foglight license (such as Foglight Agent Manager cartridges and the Foglight for Infrastructure), others may require an additional license.

Foglight for DB2 LUW is covered by the base Foglight license that allows cartridges to be installed. The SQL Performance Investigator extension requires a dedicated license.

To activate a trial or a purchased commercial license:
1
On the navigation panel, under Dashboards, click Administration > Setup > Manage Licenses.
2
Click Install.
3
In the Install License dialog box, click Browse.
4
In the file browser that appears, specify the location of the license file.
5
In the Install License dialog box, click Install License.
Documents connexes

The document was helpful.

Sélectionner une évaluation

I easily found the information I needed.

Sélectionner une évaluation