サポートと今すぐチャット
サポートとのチャット

vRanger 7.6.6 - User Guide

Introduction Configuring vRanger
Configuring vRanger through the Startup Wizard Configuring vRanger manually Supplemental instructions: additional repository types
Using vRanger Backup Restore
Restoring a physical server Performing a full restore for VMware VMs Performing a full restore for Hyper-V® VMs Performing a full restore for VMware vApps Performing a full restore of a physical machine Performing an FLR on Windows Performing an FLR on Linux Restoring from manifest
Replicate VMs Reports Integrating and monitoring vRanger Using the vRanger Console vAPI Cmdlet details
Add-BackupJobTemplate Add-CIFSRepository Add-DdbReplicationRepository Add-DdbRepository Add-EsxHost Add-HypervCluster Add-HypervHost Add-HypervRestoreJobTemplate Add-NFSRepository Add-NVSDRepository Add-PhysicalMachine Add-RdaRepository Add-ReplicationJobTemplate Add-RestoreFromManifestJobTemplate Add-RestoreJobTemplate Add-VirtualAppforLinuxFLR Add-VirtualAppforLinuxFLRVA Add-VirtualCenter Disable-Job Dismount-LinuxVolume Enable-Job Get-AddressBook Get-BackupGroupEntity Get-CatalogSearchData Get-CatalogStatus Get-ConfigOption Get-Connection Get-CurrentTemplateVersionID Get-Datastore Get-GlobalTransportFailover Get-InventoryEntities Get-IsInventoryRefreshing Get-Job Get-JobTemplate Get-MonitorLog Get-Network Get-PhysicalMachineDiskMap Get-Repository Get-RepositoryJob Get-RepositorySavePoint Get-RestoreDiskMap Get-SavepointDisk Get-SavepointManifest Get-Savepoints Get-TransportFailover Get-VirtualApplianceConfig Get-VirtualApplianceDeploymentStatus Get-VirtualApplianceReconfigStatus Get-VirtualMachinesUnderInventory Get-VmDisk Get-VMDKVolume Install-VirtualAppliance Mount-LinuxVolume New-BackupFlag New-BackupGroupMember New-Daily Schedule New-EmailAddress New-IntervalSchedule New-MonthlySchedule New-ReplicationFlag New-RestoreFlag New-SMTPServer New-TransportConfiguration New-VirtualAppliance New-WeeklySchedule New-YearlySchedule Remove-AllMount Remove-BackupGroupEntity Remove-BackupGroupMember Remove-Catalog Remove-DdbStorageUnit Remove-JobTemplate Remove-LinuxVolume Remove-Repository Remove-SavePoint Remove-VirtualAppliance Remove-VirtualApplianceConfiguration Run-JobsNow Run-ReplicationFailover Run-ResumeReplicationFailover Run-TestReplicationFailover Set-Cataloging Set-CBTonVM Set-LinuxVolume Set-MountPath Set-Resources Stop-vRangerJob Update-BackupJobTemplate Update-GlobalTransportFailover Update-HypervRestoreJobTemplate Update-Inventory Update-ReplicationJobTemplate Update-RestoreJobTemplate Update-VirtualAppliance Update-VirtualApplianceConfiguration
About us

Selecting a Destination

Previous Next



Selecting a Destination

The Destination Selection page lets you configure the host, drives, and datastores to which the savepoints are to be restored.

To select a destination:
a
Select the host from the Master Host drop-down list.
b
Confirm that the path that appears in the Virtual Machine Location field is correct. To change this path, use the browse (…) button to locate and a select a new location.
c
Click the Master Disk Storage Datastore browse button to locate and select the datastore to use for all VMs. The Master Datastore lets you select all datastores simultaneously.
d
Click Assign.
2
b
To select a different host for each VM, click the drop-down list in the Restore To Host column, and then select the host to which the VM should be restored.
4
Click Next.

Selecting a network

Previous Next



Selecting a network

The Network Selection page lets you configure the virtual network to which each network adapters should be connected upon restore. You can configure a Master Network, which will be pre-populated as the default selection for each network adaptor in the restore job.

To select a network:
To use the same network for all VMs, select a host from the Master Network drop-down list to which all VMs should be restored. Click Assign.
2
Click Next.

Configuring restore options

Previous Next



Configuring restore options

The Options Selection page displays the restore options available depending on the type of VM you want to restore.

To configure restore options:
1
On the Options Selection page, select from the following restore options:
Force overwrite: This option overwrites any existing disk or config files of the same name as those files in the destination host.
Force power on: This option turns on the VM after the restore.
Create cluster role for restored virtual machine: This option is for Hyper-V® VMs only. It attempts to add the VM as a cluster resource of the Hyper-V host parent cluster.
2
Click Next.

Setting the recurrence schedule

Previous Next


Restore > Performing a full restore for Hyper-V® VMs > Setting the recurrence schedule

Setting the recurrence schedule

The Recurrence Schedule Selection page lets you indicate whether the restore job should be done on demand — at this moment — or at a future time. To schedule a future occurrence, you must define the start time, recurrence pattern, and range of recurrence.

To set the recurrence schedule:
1
On the Recurrence Schedule Selection page, select the options as described in the following table.

This will be an On Demand job…

There is no need to define a schedule. The job runs on demand.

Start Time

The time of day at which to run the job.

Recurrence Pattern

In this section, you establish how often the report should be generated. There are five options within this section:

Daily: The daily option can be scheduled to run the report every weekday or every x number of days.
Weekly: vRanger can be configured to run on weekly intervals, from every week to every 99 weeks. The day of the week on which to run reports can be configured.
Monthly: The monthly option offers the following configurations:
Day [x] of every [y] month:

x can be any value from 1 to 31. This value determines the day of the month on which the job occurs.

y can be any value from 1 to 99. This value determines the monthly interval — for example, every two months sets the job to run every other month.

The [f] [d] of every [y] month(s):

f can be either: first, second, third, fourth or last.

d can be: weekday, weekend day, Sunday, Monday, Tuesday, Wednesday, Thursday, Friday, or Saturday.

y can be any value from 1 to 99. This value determines the monthly interval — for example, every two months sets the report to run every other month.

Yearly: The yearly option offers the following configurations:
Every [m] [x]:

m is any month of the year. This value determines the month of the year in which the report occurs.

x can be any value from 1 to 31. This value determines the day of the month on which the report occurs.

The [f] [d] of [m]:

f can be either: first, second, third, fourth, or last.

d can be: day, weekday, weekend day, Sunday, Monday, Tuesday, Wednesday, Thursday, Friday, or Saturday.

m is any month of the year. This value determines the month of the year in which the report occurs.

Interval: The interval option lets you select the number of days, hours, and minutes that should pass between jobs.

Range of Recurrence

Select the starting date and ending date:

No end date: The job recurs until it is stopped.
End after: Select the number of occurrences.
End by: Select the date by which to end the recurrence.
2
Click Next.
関連ドキュメント

The document was helpful.

評価を選択

I easily found the information I needed.

評価を選択