Chat now with support
Chat with Support

NetVault 11.3 - Administration Guide

Introduction Getting started Configuring clients Configuring storage devices Backing up data Managing policies Restoring data Managing jobs Monitoring logs Managing storage devices
Monitoring device activity Managing disk-based storage devices in table view Managing disk-based storage devices in tree view Managing tape libraries in table view Managing tape libraries in tree view Managing tape drives in table view Managing tape drives in tree view Adding shared devices
Managing storage media Managing user accounts Monitoring events and configuring notifications Reporting in NetVault Backup Working with client clusters Configuring default settings for NetVault Backup
About configuring default settings Configuring encryption settings Configuring plug-in options Configuring default settings for post-scripts Configuring default settings for Verify Plug-in Configuring Deployment Manager Settings Configuring Job Manager settings Configuring Logging Daemon settings Configuring Media Manager settings Configuring Network Manager settings Configuring Process Manager settings Configuring RAS device settings Configuring Schedule Manager settings Configuring Web Service settings Configuring Auditor Daemon settings Configuring firewall settings Configuring general settings Configuring security settings Synchronizing NetVault Time Configuring default settings for global notification methods Configuring the reporting utility Configuring NetVault Backup to use a specific VSS provider Configuring default settings using NetVault Configurator Configuring default settings using Txtconfig
Diagnostic tracing Using the deviceconfig utility NetVault Backup processes Environment variables Network ports used by NetVault Backup Troubleshooting

Configuring default settings for nvjobstart

By default, the nvjobstart command returns either 0 or 1 (0 to indicate success, and 1 to indicate failure). You can configure the utility to return enhanced job completion status codes and messages that indicate the way in which a job failed.

To configure default settings for a NetVault Backup Client, click Client Settings. In the NetVault Backup Clients table, select the client, and click Next.
3
Under Plugins, click Plugin Options. In the Plugin Options dialog box, under CLI, configure the following setting:
nvjobstart Enhanced Job Completion Status: By default, the nvjobstart utility returns the following messages depending on the job exit codes.

0

Job completed successfully

1

Job failed with error: ‘Job Failed’

This message is returned for the following job completion states:

If you select the nvjobstart Enhanced Job Completion Status check box, the utility returns the following codes and messages.

0

Job completed successfully

1

Job Failed

2

Job Completed with Warnings

3

Job Aborted

4

Job Stopped

5

Job Died

-1

Job Failed with Undefined Error

4
Click Apply to apply the new settings and close the dialog box.

Configuring default settings for post-scripts

By default, the execution of a post-script is terminated when a backup or restore job is aborted. You can modify the configuration setting for post-scripts to change this behavior.

To configure default settings for a NetVault Backup Client, click Client Settings. In the NetVault Backup Clients table, select the client, and click Next.
3
Under Plugins, click Script. In the Script dialog box, configure the following setting:
Terminate running script on Job Abort: This check box is selected by default. If you want to continue script execution even when the associated job is aborted, clear this check box.
4
Click Apply to apply the new settings and close the dialog box.

Configuring default settings for Verify Plug-in

With a backup job, you can choose to run the verification phase to check the correctness and completeness of a backup at the end of data transfer. NetVault Backup uses the built-in Verify plug-in to perform the verification phase. The Verify plug-in verifies the stream length written to the media and ensures that no blocks were dropped during backup. While the actual backup runs as Phase 1, backup verification runs as Phase 2 of the backup job.

By default, the backup verification job runs on the NetVault Backup Server. You can modify the configuration settings for the plug-in to run the verification on an alternate client or locally on specified clients.

2
On the Configuration page, click Server Settings.
3
Under Plugins, click Verify. In the Verify dialog box, configure the following settings.

Always run Verify locally

By default, the verification phase runs on the NetVault Backup Server.

To avoid data transfers over the network, you can choose to run verification locally on the clients to which the device used for backup is attached. This option is globally applied to all clients. It does not work for clients that do not have a locally attached backup device.

Comma separated list of clients that verify locally

If your backup jobs are distributed across multiple client-attached devices, use this setting to specify a comma-separated list of clients that can run the verification phase locally.

Default client to run Verify

To configure an alternate client to run all verification jobs, specify the client name.

This setting is useful if you use a client-attached device for your backups. It allows you to select the same client to run backup verification jobs.

4
Click Apply to apply the new settings and close the dialog box.

Configuring Deployment Manager Settings

This section includes the following topics:

Related Documents